Liczymy pasujące modele…
My cats tend to bite the original spout when the water runs low ( lower water results in less pressure ) Of course my cats played with the spout until it was never seen again. so I designed a replacement. The design differs from the…
A friend asked me if I could make a replacement for the Catit Pix cat waterer nozzle that her cat had lost, we got the original and I made it from scratch with fusion 360. Maybe it could be of use to another cat lover. I made it in PLA,…
Bought a Catit fountain (stainless steel one) but my cat was not using it and preferred always the tap water. It seems she likes the "falling water". Searched for an adapter for Catit for this fountain and was not able to find one, so I…
My original handle broke so I designed stronger one, based on my broken lever. Mine was printed on Creality K1 with 25% comb infill. I'm hope it would work for you.
The little black piece that attaches the pump to the flower, in the this Catit Flower Cat Water Fountain We lots one of ours (I think I accidentally threw it out?), so I used my caliper and fusion 360 to model a new one. Works great.…
An adapter to use small 5" filters, which are cheaper, and uses less plastic (hic) in a large Catit Fountain. It is recommended to use food-safe plastic. I printed with PETG.
A replacement filter for a Catit Pixi cat fountain, mainly to keep cat hair from clogging the pump but does reduce dripping a small amount. Print in PETG / HIPS or other food safe filament. Print with 0 top and bottom layers , 60% grid…
One of my cats would reach his paw up into the feeder and turn the little turnstile so that it'd dispense food. In order to prevent him from reaching up there, I made this plate that reduces the side of the opening. There are two slots…
Printed with PET-G, 100% infill, flaps down. Supports only for top rim, rest can be done without supports. It can be pretty hard to remove magnet from original shaft. I used lighter and just heated that part. Be careful not to burn…
My cats kept knocking down the Catit senses food tree so they have easier access to the food. This print tries to solve that. I designed a cup that can be filled with small stones or sand along with a lid that can be glued on top of it.…
Lid for CatIt Design Senses feeder. I noticed that our cats tended to eat just over the top opening, bypassing all the harder parts. This lid is spaced so that it's easy to slide in place, but it's tight enough so that cats can't just pry…
Catit PIXI Smart-Futterautomat ist ein Ersatzteil das auf dem Motor geschraubt wird zur Verteilung des Futters, der Portionierer . Ich habe es in PETG gedruckt und man könnte es auch in ABS / ASA drucken und Aceton glätten . Viel spass…
This part needs a strong material, I used PETG-CF but you might be successful with PETG only. You will need supports for the lower beams, and 4 perimeters or 100% infill.
An adapter to use small 5" filters, which are cheaper, and uses less plastic (hic) in a large Catit Fountain. It is recommended to use food-safe plastic. I printed with PETG.
This was a print out of necessity for an older cat who is having trouble eating lately. Hoping the elevated position will work out. Prints pretty easy without supports and I used Bambu Wood PLA for a nice finished look for where it's…
This clip retains the rubber flaps in your Catit PIXI Smart Feeder reservoir.
Threw together this cover for the carbon filter because my cats started to try and eat it. Fills pretty much an entire Prusa i3 MK2/s/3 bed. May want to scale down a bit in the z since it comes out a bit thick. This was designed hastily…
A stand that protects the water from floor heating and also looks good. The ring will fit these products: Catit (Stainless Steel) Flower Fountain https://www.catit.com/products/drinking-fountains/flower-fountain…
This is a replacement drive axle for the Catit Sense Mushroom cat toy.
I did a quick internal math check on needing 4 starter kits for the Catit Magic Blue air purifier packets, and realized i could design it pretty quickly half drunk watching Hockey Night In Canada. So i did. Simple friction fit with an…
bracket to prevent your cat from removing the cover from your catit fountain
