27 modeli
Half-height beer crate style containers for CR2032 and CR2477 coin cell batteries. Can be used separately or stacked after gluing the stacking piece to the bottom. The CR2032 container can fit 28 batteries while the other one should fit…
This is a solder-free AirTag CR2477 adapter. The CR2477 battery has about four times the capacity of the standard CR2032 used in AirTags, giving you roughly 4 years of battery life. Anyway, it turns out that at the right angle, you can…
Adapter to replace button cells batteries with AA or something similar. I used wire wrapped around the outside and some scrap nickel strip through the middle. I soldiered on a AA battery holder and now my wireless sensors have tons of…
1x1 Gridfinity Refined Battery Holder for 5 CR2477 batteries. This battery is typical packaged in quantity 5. Two versions are included, one with the label embedded, to be printed same color or by swapping filament at the end of print to…
Gridfinity 4x CR2477 Coin Battery
A bigger battery cover for fitting a larger CR2477 battery instead of a CR2450 battery. Category: Electronics
I have Ruuvitag in every room of the house measuring and storing temperature and humidity. I also have several outside in the yard and several in my 3d printers measuring chamber temps etc. I try to always have CR2477 in stock, but…
The battery in my Ecobee smart sensor died and I didn't want to buy a CR2477 battery since I had a ton of cheap CR2032 batteries from other projects. Printer settings: PETG 20% infill 2 perimeters
Nie wieder verlegte Knopfzellen! Dieser kompakte 1x2-Bin wurde speziell zur Aufbewahrung von CR2477-Batterien entwickelt und fügt sich nahtlos in dein Gridfinity-System ein. 🔧 Eigenschaften: Kompatibel mit dem offenen Gridfinity-Standard…
Very simple CR2477 to CR2430 adapter. Print Settings Printer: Bambu Lab P1P Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Any PLA Any Category: Electronics
I wanted a battery holder that I could place in a storage box and not worry that the batteries would fall out if the storage box tipped. I designed this simple holder with spring loaded sides holding each battery.
Mr Fox has a KaKu (klikaanklikuit) remote control with a hard to source CR2477 lithium coin cell. Designed a simple adapter for a (thinner) CR2450 cell, filling the gap. This remote control has both contacts at bottom. In case one of the…
BOM 8mm wide nickel strip CR2477 battery printed parts Be careful not to short the battery with the nickel strips and align the positive contact. Screw in lid is left hand thread!
Holds 2x CR2477 batteries, with some misc storage space.
I have Ruuvitag in every room of the house measuring and storing temperature and humidity. I also have several outside in the yard and several in my 3d printers measuring chamber temps etc. I try to always have CR2477 in stock, but…
This is a solder-free AirTag CR2477 adapter. The CR2477 battery has about four times the capacity of the standard CR2032 used in AirTags, giving you roughly 4 years of battery life. Anyway, it turns out that at the right angle, you can…
Half-height beer crate style containers for CR2032 and CR2477 coin cell batteries. Can be used separately or stacked after gluing the stacking piece to the bottom. The CR2032 container can fit 28 batteries while the other one should fit…
This 3D print model is a 1x1 Gridfinity-compatible battery holder designed specifically to store four CR2477 coin cell batteries . It features snug circular compartments that keep the batteries securely in place while allowing easy…
The cables can either be glued into the slots or fixed in place by carefully melting them with a soldering iron. Print Settings Printer Brand: Creality Printer: Ender-3 V3 SE Supports: Yes Resolution: 0.2mm Category: Electronics
This adapter allows you to use CR2032 cell batteries in devices that requires a CR2477 battery. Added a small cutout to make removing the battery easier.
This box is for storing 20 CR2477N batteries. To print without support. If it does not close properly after printing, the inside of the lid can be lightly sanded. Or smear the inside of the lid with candle wax. This ensures that it opens…
