Liczymy pasujące modele…
A simple stand for holding your Verizon Gizmo watch and charger. I added steel BBs to the infill of the base to provide some weight. Printed in PLA but should work with most materials.
It seems that newer Gizmo watches come with a slightly larger charger. I remixed the stand to accommodate the new one
We wanted a stand for our new router/modem for Verizon 5g Home internet cube that was wall mounted, so we could get a clear signal from the backyard and garage. It has 4 screw holes, and an inset so that the circular foot of the router…
Articulated hedgehog keychain
This a remix of the original Verizon 5G Home gateway shelf. I have added cutout holes for the cables. Printed on Ender 3V2 with PLA at 20% infill and no supports
Printed with PLA and mounted using 3M VHB Tape. Please share your Make:) Like the freebie? Feel free to buy me a cup of coffee with the link above ;)
Needed a way to keep the hotspot safe and out of the way in our RV. It has two recessed holes for screws but could also be held to the wall with 3M strips or Nanotape. Fits better without the back battery cover on the device, will fit…
Articulated hedgehog / Erizo articulado
This is a “minimalistic” wall-mount for the Verizon JetPack 8800L MiFi Hotspot. I may go back and reduce some unnecessary corners and mass to make it truly minimalistic. I designed it using a 3D scan of the device, so it should be a tight…
Modelo adorable de erizo rechoncho. Colección de mis animalitos.
This is a clip to attach a cable to a fence. Nail a normal nail into the fence, place the cable in this clip, and then hang it on the nail. If you want this already printed and mailed it is available to purchase here. I am the only one…
I needed something to protect the screen, I often toss this in my back pack when on the go. If you're going to print the pins like me, instead of using screws, you're going to need to make one end of the pin smaller after printing, I…
wall-mounted bracket for verizon gray internet box A simple, sturdy mounting solution designed specifically for the gray Verizon internet box. This bracket allows you to securely attach the box to a wall, keeping it off the floor or…
This model is for a Verizon Business Gateway (router) compact wall mount. This is NOT the same as the home version of their gateway which there are other wall mounts available for. I designed this to hug the wall pretty closely with a…
Hasta capa 20 amarillo Hasta capa 24 negro Hasta capa 26 blanco Resto en negro
I couldn't find a case for this device and plan to use it in some rough environments. My first TPU design, but I think it came out good enough to share. This is the third iteration to get it just right. Was designed with Fusion 360 to…
I wanted a waist level finder for my printed Goodman Zone v1.0 but there wasn't one available. This works with 4xM3 hex bolts utilized in other areas of the camera build along with magnets sourced from my local hardware store and a…
A mount for the Verizon Jetpack mobile hotspot. Can be mounted using Command Strips. Print at the default size with supports (tree supports if possible). All other settings are up to you. Modeled in Fusion 360.
This is a keychain with the Verizon Check logo embossed into it. Printed with PLA on an Ender 3V2 with no supports or adhesion.
Moves the Verizon FiOS I-211M-L ONT and its "Power OK" power brick out of the wall box and into a 19" rack: a two-piece 1U mount with a status-LED window, keystone passthrough for the ethernet handoff, and tool-free friction retention…
The 5G home internet router from Verizon has no option for a table or desktop stand and I don't want to mount it to a window or wall. Here is a functioning stand for it! It has a cable hole at the bottom to run the power cord and ethernet…
remixed this shelf by @HenryCrete_1056952 into a rack mount for the 3-D printable rack, Mod10 by MandicReally. Why? idk takes up 3U
ring mount for verizon Jetpack use PLA and it will snap to place make sure you print puting the lip down if you using PETG you will need to upsize it but 2% or it will be to small Print Settings Printer Brand: Creality Printer: CR-10…
Remixed a soundbar mount to work with a Onn TV and Stream TV Soundbar https://makerworld.com/en/models/1603420-samsung-crystal-series-tv-sound-bar-mount#profileId-1690401 TV: Onn 50" Model: 100133204 Soundbar: Verizon Stream TV Soundbar…
I measured the mounting feet on the modem and made some feet that securely slid in and locked in place, then put it on a random L bracket I found. The antennas should be facing a certain way, so it's not just mounted to the wall at a 90…
The cutout in the bottom holds the base of the gateway snuggly so that it won't be shaken off the shelf, and the data on the bottom can still be read without lifting the unit if mounted overhead. I also created the holes with center and…
UPDATE I don't like the minimum price of $5 enforced by Printables, as I feel it is a bit too much given the user must use their own materials and time to make one and the design is quite simple. Cults 3D allows lower pricing, so I have…
