Liczymy pasujące modele…
faucet garden adapter 4 variants M22x1 faucet → quick coupling for hose M22x1 faucet → 1" ¾" & ½" outer thread use 6x3mm or similar gasket for quick coupling Print settings 5 walls 0.1mm layer 30% infill no supports
The fine thread M22x1 is often used for in house water taps. You need in addition a O-ring and a rubber gasket for the connection between adapter and the water tap. Printed with 0.12 layer height and in PETG.
Bicycle crank cap m22x1 Print the model as it is loaded - you need to enable supports in the slicer. I used ironing when printing. I printed from PETG Nozzle 0.4 Layer 0.12 Minimum 5 walls CONCLUSION 💚💚💚If you enjoyed the project please…
Printet with PLA+ a connector between faucet and an adjustable Dual Mode Sprayer
It's a small, simple and quick print. Normally you need two sleeves for a door.
This model is an adapter that connects a garden hose connector of standard size M32 with 2 mm pitch to a standard size M22 sink thread with a pitch of 1 mm. Use a rubber gasket with an outer diameter of 18 mm inside the adapter to make…
Used on a kitchen faucet. Attention! - The part can be printed without supports - placing the external thread closer to the table. But in this case, there are problems with adhesion to the bed. For this, I added an additional cross that…
It works fine, but as the water contains no air it splashes too much back up when it hits the sink I used variable layer height and 0.12 for the threads,the rest is 0.2 Printed in green Clas Ohlson PETG
This shower faucet addon came out pretty good. Its actually what I wanted. The nozzles are directed to a center point 400mm below the faucet outlet so the water beams flows almost perfectly straght down. Print in PETG to ensure it will…
I needed a panel Nut for my potentiometer. I couldn't find any special models that met my requirements, so I made it myself, and maybe I can help someone with it. It's not fully screwed on because it has a recess for the potentiometer…
This is a simple yet effective adapter that converts a G3/4 (26.4mm) faucet thread to an M22x1 (22mm) thread. It is ideal for connecting various accessories such as aerators, water filters, or hose adapters to your faucet. The design…
This is an axle thread cover I made to help prevent rust when my vehicle is running winter tyres. This cover is for an M22 x 1.5mm thread. I recommend using PETG for this part. My experience is they tighten up nicely against the inner…
Endcap for M22x1,5 thread. I made this to protect the threads and the internals of my pressure washer attachments. Printed in PETG with 15% infill. Model should have enough clearance to screw on, scale if it's too tight for you.
Adapter M22×1 male to G1/2 BSPP male – 12 mm bore
M22 × 1.5 thread +0.40 mm built-in tolerance 17 mm standard ball joint 17.6 mm hole size for the ball to pass through 29.0 mm outside diameter
——————————————— Deutsch ——————————————— Einschraubbarer Trichter für Ölwechsel Diesen Trichter habe ich selbst konstruiert, um den Ölwechsel an den Achsen meines Kramer 312LE deutlich zu erleichtern. Bisher musste ein normaler Trichter…
——————————————— Deutsch ——————————————— Einschraubbarer Trichter für Ölwechsel Diesen Trichter habe ich selbst konstruiert, um den Ölwechsel an den Achsen meines Kramer 312LE deutlich zu erleichtern. Bisher musste ein normaler Trichter…
This model is an adapter that connects a garden hose connector of standard size M32 with 2 mm pitch to a standard size M22 sink thread with a pitch of 1 mm. Use a rubber gasket with an outer diameter of 18 mm inside the adapter to make…
