Liczymy pasujące modele…
Hi guys, welcome to my new Nanolongrange FPV drone design! This is the 4th and most sophisticated iteration. The design builds on my previous completely 3d printed frame NLR35. The goal was to make it lighter, more powerful and yet fully…
Hi guys, welcome to my new Nanolongrange FPV drone design! This is the 3rd iteration, you may know the previous versions https://www.thingiverse.com/thing:4743497 and https://www.thingiverse.com/thing:4818009 This time, the design aim was…
You can use the same parts as for the NLR35. You can get the O4 air unit <a href="https://www.banggood.com/custlink/DvGS4l0mPD" target="_blank">here</a>
Next level Racing Flight Simulator holders to rest the quest 3 controllers for those who use them
Simple mount for Nameless RC Naked 9 / 10 / 11 for common GoPro mount and iFlight mount. I design with wireslot for betaFPV bt2.0 connector. Secure with the long m2 screw comming with the NLRC kit. Category: 3D Printing
Last month, I purchase an INLretro Dumper-Programmer and began using it almost immediately. However, without a case, the solder points on the bottom of the PCB left marks on my desk (which my wife still hasn't found out about). Having a…
I created this Keyboard holder for my Next Level Racing F-GT Sim, I do not use a shifter so I decided to take advantage. It’s made to fit the Logitech K400+ keyboard. Nov 1st 2024 V2: Updated model with the following: -Split model for a…
Hardware needed: 1x M4x20 2x M4x12 3x M4 Nuts Velcro Glue/Stick a bit of velcro to the keyboard holder and back of the keyboard so you can remove the keyboard if needed. Adjust the angle of the holder and tighten the M4x20. Alternative…
Spacer to change the angle of the Next level Racing GT Lite chair. I found the standard angle was too far back for me, so I created these spacers to make the chair more comfortable. Would recommend support under the part unless your…
I found the original angle of the GT-Lite's back rest to be a bit too steep so this riser adds 10degrees to straighten up the back a small bit. print upside down. this model should not need supports.
A left hand mount to suit my Next Level Racing Elite Rig. Designed to mount the iFlag case remix by Pascalmartin https://www.thingiverse.com/thing:3148707 of Supremages' iFlag Case https://www.thingiverse.com/thing:1215138 Attaches to…
Hang a Logitech K400 PLUS keyboard mount under Next Level Racing GTELITE wheel deck. Uses M4 x 16 mm screws threaded into printed “nuts”, which fit in the 8mm x 60mm slots in the wheel deck.
Pedal End Delete X 2 + Length of Omar I don't have my pedals raised, and it bothered me that an extra useless length was attached at the end of the pedals. A plasterboard screw (black) was used to fix the NLR frame to the end cap on both…
I made this mount for the Next level Racing F-GT. Let me know if you have any suggestions. Also added test file for GTTRACK rigs. let me know if you try it?
Uses M4 x 16 mm screws threaded into printed “nuts”, which fit in the 8mm x 60mm slots in the wheel deck.Uses M4 x 16 mm screws threaded into printed “nuts”, which fit in the 8mm x 60mm slots in the wheel deck. It's a tight fit, might…
Thrustmaster Warthog AVA Base to Next Level Racing Flight Simulator Cockpit Mount. Printed on Flashforge A5M using standard PLA. 0.2 layer height 0.4 nozzzle 5 wall loops (2 mm) 15% Cross Hatch infill density 5 bottom shell layers 5 top…
This is a way to add a way to mount a H-shifter, but keeping the original shifter plate free a handbrake and sequential shifter for the Next level racing wheelstand 2.0 I printed the long version in one piece on an Prusa XL.
I wanted a way t9o mount my button box to my rig, I found this great way to attach things to the NLR seat I have, and then I used https://www.printables.com/model/1510223-pxn-cb1-mount to mount the actual button box, workes great
This is an adapter plate for the Virpil CM3 for the nextlevelracing boeing military fight sim rig. It's intended to replace the bottom metal plate of the throttle with the existing screws. An alternate version that uses much less plastic…
I needed a side tray for a mouse for my Next Level Racing Victory, so I designed this. I added a slot for the small keyboard I have as well. I found that I really only use it for my xbox controller though, since the motion of the rig…
Hand brake mount for the Next Level Racing Victory, to work with the Moza Handbrake.
I tired using the 3 screws in the middle of the button box, but after some testing I found that using two of ther 100x100 vesa screw holes would work, this made the whole part a lot more simple to make, I used M4x12mm screws,
This enlrages the Edifier W820NB to pads of steelseries arctic prime. The new pads are 10 x 8,7 cm the holes i have drilled manually. I used the already existing screw holes with longer screws.
Сделано для увеличения емкости батарей. Вес литиевых меньше веса 18650.
Headphone hanger that uses the hinge of steelseries headphones (wireless pro) as hanging point. keeps headphones even with high vibration of wheel base. I use it to connect earphones (in-ear) to use while racing used 2 m6 screws that came…
This is an adapter plate for the Virpil CM3 for the nextlevelracing boeing military fight sim rig. It's intended to replace the bottom metal plate of the throttle with the existing screws. An alternate version that uses much less plastic…
Сделано для увеличения емкости батарей. Вес литиевых меньше веса 18650.
This model is created to raise the pedal to about 20mm from the ground. I created this because i'm using Simsonn pedal and everytime i push the brake pedal, the front-end will become raised, after i add this raiser on the back, it fixed…
After i use Simsonn pedal on my NLR GT Lite, over the time of the race, the pedal plate could be diagonally pushed and not straight again after some braking. This model could help to prevent that with bigger face to hold both straight. It…
Print with nut cavity facing out, the bolt head diameter should be under 12.95mm on the flats to fit, scale accordingly
used for nlr plates to allow use of pvc to mount keyboard. like zsa moonlander
