Liczymy pasujące modele…
Un chargeur portable puissant et pratique, parfait pour les urgences ou les déplacements. Nous avons utilisé une batterie 18650, choisie pour sa capacité élevée (jusqu'à 3000 mAh) et sa disponibilité. Ce chargeur peut alimenter…
Remix or Yanev's model. I've removed the MicroUSB hole, fixed the screw holes and most importantly, I've removed the big slot to see the charge percent and replaced it with small 1.5mm holes to add a transparent acrylic rod for the LEDs.…
IP5328P module case This is a remix of 3D printed case for very popular IP5328P power bank module. This module supports 18W of charge/discharge and is capable of delivering 12V at the output. I made a remix to be compatible with the M3…
Под печать соплом 0.4мм, слой 0.2мм. Можно любым в принципе, но отсеки для светодиодов могут не пропечататься при использовании более крупного сопла (подбирать ширину лини придется). Печатал из АБС, сопло 0.4мм, слой 0.2мм, клеил…
A simplified model of a IP5306 5V 2A powerbank module for use in your projects
I needed a power bank case for my salvaged 18650 batteries. The module I used is in the link below. 5V 2A Charge-Discharge Integrated Module Type-C Input Compatible With 4.2V lithium Battery,…
Modeled and printed this back in the summer of 2022. Sadly, the battery have already degraded significantly when I finished modeling & printing this but I still see value in this model I made. Remix it on Onshape:…
The IP5328P can be installed facing up or upside down (see "ud" in the filename), which makes it slightly smaller. The version with the IP5328P facing upwards is easier to install overall, but please note the picture showing the cable…
По просьбе разработал на 2шт 18650 Под печать соплом 0.4мм, слой 0.2мм. Можно любым в принципе, но отсеки для светодиодов могут не пропечататься при использовании более крупного сопла (подбирать ширину лини придется). Модуль крепится к…
This is a 3D printable glue-fit enclosure for building a custom power bank using the IP5328P_V1.0 module and a 1260110 high-capacity 3.7V 10000mAh Li-Po battery . The design ensures a precise internal fit while offering a compact, sleek,…
Modified the original button, as my broken off during the first assembly :)
Remix of michal00ss powerbank case to fit only 2 cells instead of 5. Everything else is the same.
Longer (+3mm from the original) version for additional spring contact plates. Improved battery mount contacts: example or ozon ip5306: aliexpress or ozon battery: ozon
🔋 IP5328P-Based Power Bank – Compact and Powerful Fast Charging Module Designed for DIY projects or standalone builds, this IP5328P-powered module supports a wide range of fast charging protocols , including: ⚡ QC3.0 , FCP , AFC , MTK PE…
IS-IL03-IP5328-v1.2 - A power bank board that can be bought on the Internet and made into a power bank based on it. I only needed the front panel to repair the power bank. P.S.: Micro USB doesn't fit a bit - you'll have to cut it with a…
After three of the four hub caps decided to hit the road… there was only one things to do. These hub caps / wheel center covers fit a the MB Wheels brand Legacy model 16", 8-lug wheel. Not sure if they fit the 5-lug or 6-lug models in the…
post a pic when your done! 1、模型仅为皮肤mod，替换原版模型中的主要外型部件使用。要制作完成需要依赖原版模型文件。 2、需要在切片软件中拆分后再摆盘打印。 3、在原版模型的五金配件基础上需要替换或者新增的配件如下： 更换：3.0直径圆柱销长度32mm*1 更换：M5外径6长度35mm对锁螺丝*1套 更换：m3沉头螺丝，长度16mm*4颗 新增：m1机瞄光纤，7mm*1根，47mm*2根…
Replacement Case for IP5389 Battery Charger (18650 x8) from aliexpress https://www.aliexpress.us/item/3256804058674314.html?spm=a2g0o.order_list.order_list_main.28.bbff1802eXpBEB&gatewayAdapt=glo2usa&_randl_shipto=US. I did not like the…
Foreword : Do this at your own risk, LiPo's can be spicy : ) Note that this case is designed specifically for 5x18300 cells and the IP5310 charge controller! I hate seeing useful electronics go in the trash so I collected several…
Full description and build instructions available on https://github.com/Devnol/Juicebox
designed to be attached with m3 screws minimal supports required you can see my messy design in onshape
Another, more durable version of an IP5328P powerbank housing. Material: Transparent filament can be pushed through the holes in the housing to act as light tunnels for the IP5328P-LEDs. Use 8x M3 10-12 mm countersunk head screws to close…
This is a remix of the Lenovo P53 dock model by TH_Solutions on Thingiverse (link below). The only difference with this model is it's split into two STL's to make it easier to maneuver and set up on a printer. Photo is in progress photo…
A snap-fit case for IP5328P and 3x 18650 batteries.
## Design Concept This 3D model represents a sleek and functional power bank case designed for use with the IP5328P controller and up to six 18650 batteries. The case is tailored to offer a balanced mix of portability and power capacity,…
we put the coffee maker (https://amzn.to/3GntakU) on a tray (https://amzn.to/35ThLwH) to save our wooden furniture. However, the problem was that the coffee machine rattled at the edge of the tray and was slightly tilted. so i designed…
wanted a simple powerbank case so I made one with a 3.7v 10000mah battery from a broken powerbank BOM Similar battery to the one I use x1 IP5328P Board x1 M3x20 screws x4 M3x6 screws x2 Double sided tape a little bit
TPU You can use a long screw from the DIY selection or an M3x8 screw.
Minimalist vertical stands for Thinkpad P53 and X13gen4 - stable and usefull when you want to used 2nd display. I recommned to print it from PET-G. Even though the stand was designed very precisely, I recommend sticking soft adhesive tape…
Support for attaching a Lenovo P53 Power Supply brick to an Ikea SVALNÄS rail. just print: Lenovo_SIDE (x2) Lenovo_BACK Lenovo_FRONT Lenovo_BOTTOM (x2) and press-fit assemble the support. Fix the support using an M6 Bolt or the SVALNÄS…
Spare handle for water tank in coffe machine Philips series 5000 EP5345-10. PETG, 4 walls, 30% infill recommended.
Hold your surge protector at the top of the table without the need to damage the top of your tabletop. The holder slides into the slot at the surge protector bottom. You can then screw it to the bottom of a 18mm tabletop with 3.5x16mm…
I needed a power bank case for my salvaged 18650 batteries. The module I used is in the link below. 5V 2A Charge-Discharge Integrated Module Type-C Input Compatible With 4.2V lithium Battery,…
Longer (+3mm from the original) version for additional spring contact plates. Improved battery mount contacts: example or ozon ip5306: aliexpress or ozon battery: ozon
