Liczymy pasujące modele…
After damaging a few propellers, I made these Propeller Guards. Can't say they make the Drone anymore crash survivable… But, they look cool. They are labeled for their position on the Drone: Right Front (RF), Left Rear (LR), etc… Will add…
The shade clips onto the remote controller to prevent glare whilst flying. It still allows for antenna adjustment if needed. Best to print vertically, with a small raft to increase bed adhesion if necessary. PLA, 0.2 Layer Height, 5mm…
Landing gear Potensic ATOM/SE New design and model Atom Can record video without seeing the ski legs (wide angle legs) May be seen slightly when adjusting the camera angle down to the ground 90 degrees (only when turning and stopping…
I wanted a small, hard, case for my drone. It fits in the case with the battery, camera cover, velcro strap and the cable to connect to phone . Snap fit design! *1/7/26: A number of community members have noted that the Potensic Atom-2…
Landing Gear Grip
I designed it to be foldable for easy use and storage. I used ABS for this print because it is flexible. And you need to find a 2mm steel rod, 5cm long, to use in the joints.
Slide your Atom 2 drone into this sleeve to protect the propellors during transport. Less bulky than the velcro strap that comes with the drone. Also protects gimbal if you've lost the gimbal cover. I use this in the soft carry case that…
its a sun shade for the controller pictured is an iPhone 6, but it still completely covers the screen on my 14+
The Potensic Aton 2 batteries if you store them in the charger they are designed to go into a sleep mode and discharge them to 0%. If stored outside of the charger over a period of 2 weeks they will discharge to 70% the to 50% and stay…
Parabolic antenna reflector for the remote of the potensic dreamer pro. I dont think it works for the potensic dreamer 4k, which uses the phone's wifi. I use sticky spray and aluminum foil as seen in the picture. I reached the 2000m…
Designed to replace the velcro strap that comes stock with the Potensic Atom 2. Will fit the first Atom as well. Printed the bottom piece out of PLA+ at 20% infill with supports. Printed top piece out of TPU no supports.
Its janky and obstructs the screen a bit but it does boost the distance I am able to fly up to 1km in neighborhoods, where there is WiFi, 5g, 4g, 2.4g, and other things messing with it
The design is inspired by the Hover Air drone. It is designed to be assembled and glued. The files are optimized for perfect balance and work just as well as the original body, but without the camera or front light, which I removed for…
I made a wall hanger mount for my Potensic Atom charger. Printed Pla no supports Holes are 4 mm
Case for the Potensic A20 drone, controller, batteries and charging cord. Lid is designed to be friction-fit, should stay on pretty solidly.
Krytka ramene dronu Potensic Atom 4K.
A replace of propeller protection for Potensic T25 drone. this version has interchangeable pegs. if desired, instead of the pegs you can use metal rivets with a diameter of 2.4 mm for a length of 6 mm. Print with 100% infill at 0.15…
A replace of propeller protection for Potensic T25 drone. Print with 100% infill at 0.15 resolution.
Here are some TPU feet for the Potensic Atom 2 drone to protect the landing gear. I printed it with a 0.6 nozzle with 0.24 layer hight and it works well.
este es un soporte lo cual podremos poner el movil ,sin tener que esforza demasiado el mando y poder poner tablet o movil mas grande,aparte un acople para sombrilla,en tolerancia a la hora de imprimir poner 0,1 + y -0.1
This remix adjusts the strap retention hook to keep the one side of the strap more permanently attached to the base. It also adjusts the measurements of the base to allow a tighter fit on the sUAS and prevent as much shifting. The strap…
It is a remix of the model addressing following needs: merged 2 casings to store 2 batteries enlarged battery lock, as the original was ~1 mm thick and snapped out scaled up width/depth by ~0.1 mm as the casing was too tight and creates…
Remixed Ed Golda remix for 2 battery. :) Box for 3 batteries for the Potensic Atom 2 drone. It may also fit the first edition of the Atom. Added one more battery compartament.
Here are some TPU feet for the Potensic Atom 2 drone to protect the landing gear. I printed it with a 0.6 nozzle with 0.24 layer hight and it works well.
This is an adapter/phone holder for the Potensic Drone D58 Remote. I found the extendable holder on the remote would not open far enough to hold an iphone xr that was in an Otterbox or other robust case, especially without hitting the…
Ursprünglich eine Litphane Box aber hab festgestellt, sie passt perfekt zur Drone.
This is a holder for the Potensic Atom Batteriecharger. You can hang it on the Wall or Where ever you want: [When it don't fit] Introduction: 1. Print it 2. Take a Hairdryer and heat the front of the Model 3. Take the Charger and press it…
I didn't want to carry the charger with me so i made a easy to print case for the batterys with a tab so it locks in. Printed in Pla no supports
