Liczymy pasujące modele…
What up nerds, here's a plate to add an optic to your sweet Taurus G2/G2C/PT111, etc… It dovetails into the stock rear sight mount, and uses the original screw to make sure it doesn't slide out on ya. I have the spacing for a cheap…
A porta-potty, or portable toilet, is a self-contained unit designed for temporary restroom access in areas without permanent plumbing. HAPPY PRINTING!!
Einfache Schablone für 1LE = 40mm
Die Aussparung in der Mitte muss auf der Eckfrequenz liegen.
CPAP and Wire Guide for RatRig Vcore3 ^300 with PT1000 mount and shelves Please upload your makes, would love to see them
Portable AC exhaust to 6 inch dryer duct connector adaptor FRA113PT1 Connect Frigidaire FRA113PT1 portable air conditioner with 6inch flexible dryer duct. I bought this portable AC used, it didn't come with the duct or duct connector so I…
For another clamp size, open the Fusion file and change the thickness (like in the Photo) You can also add text in your slicer, like in the photo. Label Clip for Phoenix Contact Marker für Klemmen
You need x5 m3 40mm screw x1 m3 10 screw and x4 m3 nuts. Molded sock fits like a glove on pt100 volcano heatblock
UPDATE: I've used 4inch duct for few days, but I felt like its restricting flow so I switched to 6 inch duct. You can use this design if you absolutely need to use 4 inch duct but I recommend 6 inch duct. I designed an adapter for 6 inch…
A first attempt at 3d modeling cloud strife cosplay pieces. This is a first 3d modeling test.
Case for E3d PT100 amplifier. Print instructions I used PETG, but can be printed using anything. Board simply encased between both halves. Board placed on half with pins, and the other half with holes simply closes on top. Print as is.…
E3D PT100 AmpBoard Snap Case and Mount This is a snap case for the Amp Power Board for the PT100 Temperature Sensor No supports. There is a post and back for attaching to the wire routes for the YZ Case (Einsy Rambo Board) for the Prusa…
I created this hose adapter to fit over and reduce the 60mm dust extraction port to a 35mm vacuum hose - specifically for use with a Triton TPT125 Thicknesser. The ends of the adapter are tapered to create a push-fit. It may not fit your…
A replacement disassembling latch pin For the Tarus Millennium G2. Mine flew away while I was doing some maintenance. I recommend using a solvent resistant material like nylon to print it, but PLA should be fine.
What up nerds, here's a plate to add an optic to your sweet Taurus G2/G2C/PT111, etc… It dovetails into the stock rear sight mount, and uses the original screw to make sure it doesn't slide out on ya. I have the spacing for a cheap…
The dust shute on the Triton TPT125 has an outer diameter of 54mm, whereas my shop vac hose has an outer diameter of 35mm. I designed an adapter to connect the two. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No…
Replacement for the Original Ironsight of a Taurus PT1911 Gun. Stepfile is Included if non of the Present Heights match. Different Heights Availible for Zeroring. Testprinted it on a Core One Plus with PLA+, Use the Highest Detail Setting…
If You have bought the Stearman PT17 fra 3d labprint: https://3dlabprint.com/shop/stearman-pt-17-kaydet/ With this hack, you dont need to reverse the shaft! (This includes only a hack - not the starmotor! You might have realized that You…
Safire Camera SF-IPPT111HA-2E-W Holder you can use for a wall in two positions: up and down.
I made these for my neighbor's PT17 model plane. His brackets broke and they were not being made anymore. They are made to stick right into the foam and be glued in. There are two different types of connectors that I designed but he used…
for a class project, either a scraper or a bolt tightener.
had to make this my threads were messed up when it threw a red dot and ripped the threads so i rethreaded for a largeer screw will neew sanding to fit good update first one is two narrow for the pt140 so i made some changes and widend it…
had to make this my threads were messed up when it threw a red dot and ripped the threads so i rethreaded for a largeer screw will neew sanding to fit good update first one is two narrow for the pt140 so i made some changes and widend it…
What up nerds, here's a plate to add an optic to your sweet Taurus G2/G2C/PT111, etc… It dovetails into the stock rear sight mount, and uses the original screw to make sure it doesn't slide out on ya. I have the spacing for a cheap…
4 tuercas m3 4 m3x6 2 m3 Print Settings Printer Brand: Creality Printer: Ender 3 Pro Category: 3D Printer Parts
Battery cover replacement for Intellitouch PT10 Tuner, not an exact contour match, but it will do the job effectively. Print flat face down with supports.
The FDG-Concept1, the fastest commercially available 3D printed RC Car. With 4 years of design and development behind, its design is truly tried and tested. It is a rear-wheel drive, 1/8th scale monster and if you're brave enough, it can…
Replacement for the Original Ironsight of a Taurus PT1911 Gun. Stepfile is Included if non of the Present Heights match. Different Heights Availible for Zeroring. Testprinted it on a Core One Plus with PLA+, Use the Highest Detail Setting…
Replacement for the pad that tends to fall off the Soldapullt III when it springs back. It seems to be more comfortable over long periods of use.. and stays attached better than the pad that came from the factory. Hit me up EDSYN. Would…
This is a replacement Bezel Clamp for a Starret 120 and maybe other models. The original part number is PT19046. Have not yet added slight curve in the piece that actually touches the bezel and hole is not quite at a factory finish but…
This is a little insert i made for mounting a pt100 sensor behind Busch-Jaeger blank plates. It also has a spot for 2 WAGO 221-412 clamps on the back to make installation easier.
4 tuercas m3 4 m3x6 2 m3 Print Settings Printer Brand: Creality Printer: Ender 3 Pro Category: 3D Printer Parts
You might need to play around with some dimensions to get the correct size for a specific individual.
