Liczymy pasujące modele…
Wall mounts and connectors for 120mm fans to connect together and make a wall of 360mm fans to help the Rosewill RSV-R4000U case have the adequate airflow it needs. Wall mounts just screw into the side of the case using a couple of the…
Print the adapter and use the 2 smallest enclosed screws from the HomeWizard watermeter to mount it. You have some room to align it well. I found it the easiest to let some water run so the meter is spinning. Then it's quite easy to align…
This base was designed for to replace the standard square plastic base found on many generic trim routers, and in the case, specifically the Ryobi RTR400S and RTR300 and generic trim routers. It will allow the fitting of a range of common…
A wallholder for Logitech Wireless Presenter R400. Might also fit R700 Category: Computer
This is a snap-on magnetic mount for attaching polarizing film to Flashpoint RF-400/Godox AR400 for photogrammetry purposes. It uses 4 magnets 90 degrees apart so that you can easily alternate between polarized and nonpolarized in order…
This is made by the R400 Sensus 620 Water meters. There are already 2 mounting recesses on the glass, these are used to place the holder over it and to place the sensor perpendicular to the metal. You can attach the adapter using the push…
A Air Filter for a "Attwood Turbo 4000" 100mm fan. The fan is rated for 390 m³/h air throughput. The filter consists of a HEPA and a Carbon filter stage. The 'grid panel' should be printed without top or bottom layers. You will need: 4x…
Uses 3 standard utility knife blades. Needs 2x M3x20 and 1x M3x25 screws and nuts. Stack the parts in order: a_cover, a, b, c, c_cover. Should be pretty straight forward. Cut the coax, push it in all the way, clamp down, and spin the…
Polarizer ring for photogrammetry. Plexiglass used was 3mm and the magnets were 5x2 mm. Video of assembly avaliable at https://www.youtube.com/watch?v=c8eMhpucD88&ab_channel=TheDirtyBassett Category: Camera
Fixing up an old Honda XR400 for a friend and I found the instrument panel was loose as the mounts had broken off the rear. This seems to be a common problem and this plate needs tp ne glued and screwed to the back, use M8 bolts to hold…
I recreated the model from Snowstorm to fit it my 12mm sensor, I re-used the buttons.
Prints without issue at 0.2mm layer heights without supports on Prusa MK4 with input shaping.
19 inch rack anti-sag bracket for QNAP TL-R400S Print the bracket on the side. You need two brackets, one of them mirrored in the y-axis in the slicer. No support material needed. Included is the f3d file
This LMR400 10mm diameter coax clip is 25.4mm high by 63.5mm long. It allows someone to attach 1 circular piece of coax together with the main loop of a Magnetic Loop Antenna to lower the frequency of the loop. It's just a way to clamp…
Remodelled the Makita base plate provided by Alexandre Chappel to suit a Ryobi RTR400-S trim router. Incorporates my base Adapter Plate for Ryobi RTR400-S Trim Router Original model can be found at his website here . His original YouTube…
Print at 0.1mm layer, 100% infill. Rotate 180 degrees, like a pyramid. No supports needed. Imprimir a 0,1mm de capa, 100% de relleno. Girar 180 grados, como una pirámide. No necesita soportes.
This is for LMR400 or any Coax line that is 10mm diameter. This cable clip holds one loop of coax about 35mm (1.5 inches) from another loop of coax. It is for a Transmitting Loop Antenna, to add another full loop to lower the frequency of…
My triple slot GPU was running a bit hot on the NR400 despite having 3 intake fans installed, so I made this to improve the airflow to my GPU by mounting it right behind the fans on the front of the case, on top of the hard drive cage on…
After my tripod fell over, I needed to replace both knobs . Instead of buying the full Tilt/Pan Control Crank , I designed this replacement knob . The original knob is round, but I made this version easier to print Requires a 4 mm drill…
I wanted the AM06 Pro out of its plastic box and under a proper 120 mm fan, with every port reachable and nothing cut off the stock cooler. This is a from-scratch open-frame tray, inspired by Th3Rom3’s AK2 Plus case (…
Manfrotto R400 locking pin - we lost one lock when it "jumped" out while replacing articulating knob. Print in PETG for better flex than PLA.
Manfrotto R400 replacement knob. My students broke articulated knob and wanted to make more rigid one (in 3rd picture there is one in the out of focus). Print in PETG, original screw fits great.
My triple slot GPU was running a bit hot on the NR400 despite having 3 intake fans installed, so I made this to improve the airflow to my GPU by mounting it right behind the fans on the front of the case, on top of the hard drive cage on…
I recreated the model from Snowstorm to fit it my 12mm sensor, I re-used the buttons.
Mounting the QNAP TL-R400S and other shallow depth equipment from QNAP with the provided rack ears leaves the device sagging, previously I used a tower of bricks to hold it up right but no more! The generic bracket made by Thingiverse…
This is the base plate that comes with a Ryobi RTR400-S 400W Trim Router. Print this either as a replacement for an existing one (STL) or to use to build upon for various jigs and attachments (STEP).
Design Measured off the OEM junction box cover to your left. Next a painstaking exercise in OpenSCAD scripting. The previous installer didn't realize that the covers are mirrored, so they cut cable holes in both covers exactly the same. 🤦…
Shimano Pedal PD-GR400 spikes are quite long. This is 3mm spacer that lower the spikes if you want...
I have changed my router from Keenetic back to TP-LINK Archer VR 400 version 3 since the new one is more stable and supports 2.4G and 5G split… And there was a necessity to design a new wall-mount. I printed the model on Bambu with PETG…
