Liczymy pasujące modele…
Spend $20 for rack-mount ears for my Cisco 10-port switch!? Forget that! These printed ears are MORE than strong enough at 30 percent infill, even with some other stuff stacked on the switch in the rack. My SG300-10P used 12mm long M4…
Nozzle for vacuum cleaner Electrolux Ultra Silencer ZUSG3901. I made also another one for computer cleaning with a hose. See https://www.thingiverse.com/thing:2739851 Category: Household Supplies
This is a rack ear meant for a Cisco SG300 series switch, specifically the SG350XG. The bolt pattern is 20-28mm squared (20,24,28 steps) so it's a bit more universal. I'll be posting a very similar one as a universal rack ear that's not…
printed in PLA 0.2 standart Sovol SV01Pro slicing profile. minimum bed size 280 x 240. there are 4 places for RJs network jacks in case you dont have the female/female RJ, you can make a 2" cables with one RJ on each end. In case you have…
This is the 3rd gen of my StormGuard series, this time its 3d printable. i got sick of using cardboard and it just felt easier to print this. I am going to add on making SG4 soon but for now this is what i have. Yes this works. Just…
Hose adapter for vacuum cleaner Electrolux Ultra Silencer ZUSG3901. You can use this to clean your computer (small places). You can use it with a hose of 12 outside diameter. Warning: don't use it to long because your vacuum cleaner will…
Support for Cisco SG300-20
Brauchte schnell einen Wandhalter für einen Netzwerkswitch in meinem Fall einen TL-SG3210XHP-M2 der Halter passt natürlich für alle Switche die 44mm hoch sind. Druckzeit ca. 4h
Rack mount for TP-Link TL-SG3210 network switch in 2 variants. With or without window for cabels and etc.
Specifically adapted for the Cisco SG300-10 switch. I created it because the switch didn’t fit well in the existing 10" mini rack setup. This version allows for a secure and accurate mount of the Cisco SG300-10 in a 13" rack environment.…
I needed to mount my switch in my 10 inch rack and could not find any brackets for it so I made these. Could be used for other equipment.
This is my version of a dual Cisco SG350 bracket. These are basically 19 inch rack mountable, but since I don't have a 19 inch cabinet here in my home office I just designed these. In theory they could fit other 19 inch equipment. Print…
F*cked up the ASG32 wing tip wheel. Designed this as an intermediate solution to operate the glider while waiting for spare part. (Had the "ok" from the manufacturerer to operate it like that) Uses the standard hexagonal screws to mount…
I had my Graco gun go down on me during a job so I created this model for the Graco sg2 and sg3 spray guns I hope it helps. If there is any adjustments needed please let me know.
Rack mount for TP-Link TL-SG3210 network switch in 2 variants. With or without window for cabels and etc.
I had my Graco gun go down on me during a job so I created this model for the Graco sg2 and sg3 spray guns I hope it helps. If there is any adjustments needed please let me know.
TP-Link SG3218XP-M2 Rack Ears, I put mine in a safe place that was so safe I couldn't find them so I had to model them. Strength wise, while prototyping I was printing them at 0.24 on the lowest quality/quickest settings and it somehow…
This is a mount designed to hold a Netgear SG308 switch (also works for a GS305PP - thanks Sagooinc@Makerworld), but it should hold about any switch that has similar dimensions (158x101x27mm). I measured a few of my 8-port switches and…
