Liczymy pasujące modele…
Sometimes your lamp needs to hang a bit higher. If cutting the cable is not the solution you're looking for this elegant shortener may be of help. In fact it makes a loop in the cable which is neatly covered up by a lid. The place…
I have some hanging lamps above my diner table but they're in the way when I want to fold clothes. I designed this cable shortener to be printable without supports, be elegant and to use little material. My cords are 6mm but the design…
Shorten cables for your hanging lamps.
This is a device for shortening the wire or cable of a pendant light. You wrap the cable around it and feed the ends trough the hooks. More turns, shorter wire. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports:…
This is a handle that can be used to shorten a leash for walk-training a dog to help increase control and avoid buying a whole bunch of different length leashes. When dogs are young, they need a very short leash to learn to stay close by…
Lamp cable shortener for a 6mm cable. Feel free to design some inserts for the inner diameter.
I extended the length of the original model to shorten a cable for around 40cm
This is a headphone cord wrap specifically designed for the Bose AE2, but should work with any cords that are ~1.7-2mm in diameter. I find the stock cable way too long and this was an easy solution. When importing into slicer, I suggest…
A watch band shortener tool remixed from two designs that requires only a metal pin. In picture a 1cm needle part is used (half of it goes deep inside to keep it firmly) which works really well. You need a base, pusher and a knob. There…
This model will shorten your cable by 28cm
Print with whatever layer height, 40% infill, 2 perimeters minimum, I recommend HTPLA (PLA+ / PLA Pro), but PETG and other slightly flexible filaments should work too. I have not tested in standard PLA. Assemble by sliding the two halves…
Modification part. for Dollfie Dream III body. shortens the torso by 5mm to reduce the waist seam gap, and give some variety
I had a problem with a lamp hanging too low so I was hitting it with my head all the time. Grew tired of it… so enter a ceiling lamp cable shortener.
Overview and Background My lamps were hanging too low, however I didn't like to cut the cord shorter because I wasn't sure about the optimal lamp height. This was more fun Edit the cord thickness or remix in general at Onshape
Gym rope handles are uncomfortable, so I created this. Increased handle surface area for comfort. Hold the top of the handle to grip higher (shorten rope). Contains two versions for different nut size Hardware: 8 m4 screws with length ≥…
This is an very simple yet effective helper to shorten any too long straps without a sewing machine (and temporarily, because your body might change) It's made for a 38mm Strap - to adapt it to any strap size just scal Z-height Category:…
The original Headset band was too long for my head - or become enlarged over time. This model can be used to make the band shorter. If you need it even shorter, you can use two or even 3 models on the band. Material: PETG for its…
Simple part whipped together with tinkercad to provide another mount point for shower head. In this case the “slot” tapers from 22-24mm and the handle was around 25-27mm. I printed with 3 perimeters and 15% gyroid using PETG
Similar to other brands, this shortens the cable more neatly than the included do-hickey Category: Audio
Non-destructive curtain shortener (no need for a cut). Useful for my another model - https://www.printables.com/cs/model/727156-blinds-wheel-kolecko-na-zaluzie
Just a simple bar to wrap a cord around to shorten and move out of the way. Here is the TinkerCAD link for those that need to resize.…
Basic remix of original model - extended for 2 inch belt.
Shortener for 3mm filters for a pipe Print the model according to the desired length of the filter. Insert the filters into the slots and cut.
A remixed cable shortener for lamps
The straps for my kids protective gear were too long and they had difficulty using it. I was thinking about putting a tie on it, but ended up designing these strap shortener buckles. When you are on the younger side of the 9-12 years old…
This is a simple clamp that can be used to cinch up a cord on a ceiling-mounted hanging lamp. The parametric FreeCAD file is included if you need to size it differently for your purposes; just change the values as necessary within the…
Just a simple bar to wrap a cord around to shorten and move out of the way. Here is the TinkerCAD link for those that need to resize.…
Non-destructive curtain shortener (no need for a cut). Useful for my another model - https://www.printables.com/cs/model/727156-blinds-wheel-kolecko-na-zaluzie
