P
PrintablesOss
GMC Sierra (Silverado) 1999-2006 wideband mount (Under vent pocket)
This model I created to mount the wideband in my GMC Sierra 2006.
- Pobrania
- 299
- Polubienia
- 37
- Ocena
- 0
Wyniki wyszukiwania: wideband
Liczymy pasujące modele…
P
PrintablesNRK Engineering
Mounting bracket for Haltech WB1/WB2 wideband controller
You can remix this bracket (or drill your own holes) to mount a Haltech wideband controller to something. The controller is mounted with M6 bolts and nuts.
- Pobrania
- 136
- Polubienia
- 4
- Ocena
- 0
P
PrintablesJoseph DAndrea
AEM 30-334 Wideband Gauge to Go pro mount
This mount allows you to use GoPro mounting hardware for your AEM 03-334 wideband. I created this because I didn't care for or couldn't find commercially available solutions (I have a C6 Corvette Z06), and I didn't want to drill into my…
- Pobrania
- 128
- Polubienia
- 4
- Ocena
- 0
P
PrintablesCaden127
Miata AEM wideband gauge vent adapter
printed with Hatchbox PLA on Prusa mini. Use supports.
- Pobrania
- 82
- Polubienia
- 13
- Ocena
- 1
P
PrintablesAudiotec Fischer GmbH
Helix Compose Ci5M50FM-S3 wideband speaker stand
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended.
- Pobrania
- 48
- Polubienia
- 2
- Ocena
- 0
P
PrintablesHelio Ribeiro
Fueltech WB O2 Nano Wideband Gauge mount for Subaru Forester/Impreza (central air vent)
A gauge mount installed on the center ventilation, for the Fueltech WBO2 Nano Wideband monitor, but can be modified for any other situation.
- Pobrania
- 38
- Polubienia
- 3
- Ocena
- 0
P
Printablesmoosetrain
AEM wideband double din gauge mount
Backing plate to mount AEM widebands to a double din slot. Mounted in a 300zx double din facia. The back is mounted to the facia using double sided tape. Printed on a bambu xc1 using PLA. Recommend PETG or other filaments due to cabin…
- Pobrania
- 33
- Polubienia
- 3
- Ocena
- 0
P
Printables@doegox
Handle for wideband antenna LogPeriod1 SinRally
Handle based on a hand saw handle. It matches the SinRally LogPeriod1 SR_LDP001_V106 290MHz-1.1GHz wideband PCB antenna but can be easily adapted to other wideband PCB antennas. Both parts are assembled with three M3x20 bolts and nuts.
- Pobrania
- 28
- Polubienia
- 2
- Ocena
- 0
P
Printablesmuchomas
Elecraft DL1 Wideband Dummy Load Enclosure
A single piece enclosure for the Elecraft DL1 Wideband Dummy Load kit . This close-fitting enclosure is open on the bottom, to allow use of the rubber feet included in the DL1 parts kit. It has an open grill over the resistor grid to…
- Pobrania
- 21
- Polubienia
- 1
- Ocena
- 0
P
PrintablesEJ20G
Bosch LSU 4.9 wideband lambda sensor
A mockup LSU 4.9 wideband lambda/o2 sensor. Usufull to find the perfect location of the sensor bung when building custom exhaust on car or bike. Based on a official Bosch LSU 4.9 CAD. Only sensor tip is cut (to avoid clashing into the…
- Pobrania
- 12
- Polubienia
- 3
- Ocena
- 0
P
Printablesbwaslo
Parts for a low noise wideband MEMS studio microphone
I recently posted a model for some parts for use with a MEMs microphone chip (Knowles SPH1878LR5H-C) to make a measurement quality microphone that has extremely even response over a very wide frequency range and with omnidirectional…
- Pobrania
- 8
- Polubienia
- 3
- Ocena
- 0
P
Printables
Bosch LSU 4.9 wideband lambda sensor
A mockup LSU 4.9 wideband lambda/o2 sensor. Usufull to find the perfect location of the sensor bung when building custom exhaust on car or bike. Based on a official Bosch LSU 4.9 CAD. Only sensor tip is cut (to avoid clashing into the…