116 modeli
A remix of a remix This is made to fit mil spec buffer tubes but the original 5/16 bolt is just too large and loose for my needs, So I added a insert to make the screw size smaller to M6 which is better fitting for the tube and double the…
Xmod rc car rim pack. all are stock offset and spacing. Some are remixed parts off thingiverse, some are original design. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament:…
Xmod RC car tires, a bunch of treads Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .15 Infill: 100% Filament: overture tpu black Category: R/C Vehicles
I have remixed this to work with xmod RC cars. Used with classic mustang or classic camaro front clips. Versions: V2 - shortened slightly due to wheelbase issues. also moved the front clip slightly, rear clip is still too tall, but will…
These are the axle gears for the short chassis (the red body) in all 3 gearings or colors 26 tooth green 24 tooth orange 28 tooth stock Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill:…
Front Knuckles for Xmod RC Gen2/evo/evolution Car. Mirror the hub for opposite side. I printed them back side down with supports to get the cleanest results on the hub for the bearings. Category: R/C Vehicles
UNTESTED PROTOYPE: WORK IN PROGRESS Hexmod Axle replacement Changelog: V2: shortened the 3 posts to fit better. Category: R/C Vehicles
This is a 3D printable STL file of a 69 Charger Xmod elegantly covered with a sleek black fabric, designed for impactful vehicle reveal presentations and displays. The model captures the anticipation and excitement of a new car unveiling,…
Xmod Truck oversized tire and rim It is the MAX size you can fit on a truck, I will design one 10-20% smaller in the future. but this works well. tpu Tire Category: R/C Vehicles
Pack of rims for the xmod trucks, use with bfg all terrain tires. (and stock) Category: R/C Vehicles
3D printed full front chassis for a 2.4GHZ conversion Feel free to add comments about improvements! I am constantly working on it! I tried to optimize it for 3d printing, with the least amount of supports possible. THIS WILL NOT WORK WITH…
Pair of front steering knuckles for xmod RC car. The steering linkage is thicker than stock to help with durability when printing with supports. Bearing tolerances are very tight. you may need to clean them up after the print. Changelog:…
Remix of Xmod wheel allows for more room in center to fit on the shaft. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Stock Xmod Gen1 Chassis Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Xmod RC car Gen1 Rear diff Wanted a solid rear end for one of my cars. Quick and easy print/install. 18T to match the stock diff. I was worried about the strength of the part, Printed in PLA it seems to be holding up really well. V2 is a…
Xmod Gen2 Car Evo Stiletto Chassis 3 files. Chassis bottom Chassis bottom reinforced Chassis top support Category: R/C Vehicles
Xmod Trukin Lift kit brackets for the Truck line of Xmods To print the A arms. just mirror them to get the opposite side. Rods used for a arms: amazon.com/gp/product/B07KY9578R Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts:…
Xmod wheel nut, slightly longer for better printing. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: No Resolution: .2 Infill: 100 Filament: generic abs Category: R/C Vehicles
Xmod conversion to 9g servo from stock servo. have included the servo horn to go with it. (may revise the servo horn later) Change Log: V2: cut out for the axle, slight overlook in last design V3: Arm for more stable servo V4: has tube to…
Solid rear diff for Hexmod RC cars. I printed standing upright with supports on the bottom. so far it has held up through 3 battery charges with 0 issues. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes…
Xmod Car Drag Slicks Collection some use a standard rim some require a wider rim, work in progress. (thinking I will widen one of my steelies) Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .15…
Rear A arms for xmod RC car Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Suggest you print from pla because its a softer plastic. All the bearings for xmod RC. Small ones for wheels and axels, large one for diff on GEN2. small ones will work on the GEN2 as well Print Settings Printer Brand: Prusa Printer: I3…
These gears are to help slow down the front tires. for every 1 turn of the front tires the rear will turn 1.75. should improve the drifitabiltiy. I have not tested this, I do know the gear mesh is correct, not sure if they actually work…
AAA battery holder for XMOD RC car. Contacts: https://www.amazon.com/gp/product/B07HRTRQLP and https://www.amazon.com/gp/product/B07HRSJ6NX Changelog: V2 -- moved the clip to the correct location. Print Settings Printer Brand: Prusa…
This is an xmod gen 1 brushless motor mount. it was designed for an ebay 1/28 motor. Uses the same method for tension based gear mesh. has slotted holes to allow you to rotate the motor depending on other electronics. Fits very well in…
Gen1 front and rear top frame supports ChangeLog: V2 -- Added the holes for the rear clip. was an oversight in the design Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: No Resolution: .2 Infill: 20 Filament:…
Xmod RC Rear Axel Bearing Holder Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Rear chassis for Xmod rc car. Changelog: V2 a lot of fixes. various things. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .2 Infill: 100% Filament: generic PLA Category: R/C Vehicles
Rear axles for xmod RC Use with my solid diff or standard xmod diff Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: No Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Front A arms for xmod RC car Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100% Filament: generic PLA yellow Category: R/C Vehicles
Rear diff for xmod EVO 2/3 generation will work for 2wd and 4wd. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
These are the axle gears for the long chassis (the yellow body) in all 3 gearings or colors 26 tooth green 24 tooth orange 28 tooth stock Category: R/C Vehicles
Xmod RC car smooth tire (oem style) Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .2 Infill: 100 Filament: overture tpu black Category: R/C Vehicles
Replacement shock for Xmod RC cars. THIS WILL NOT FIT THE EXISTING SHOCKS. (had to modify to make for easier printing. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament:…
Xmod Gen2 Car Evo Rear A-Arm Wide is from the later model xmods better/stronger. Mirror the arm for opposite side. Rod used https://www.amazon.com/gp/product/B07KY9578R Category: R/C Vehicles
Xmod RC Motor mounts front and rear Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Rear Suspension Mounts for Xmod RC Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Front mount for upper control arm for Xmod RC car. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100% Filament: generic PLA yellow Category: R/C Vehicles
Xmod Gen2 Car Evo Front A-Arm Mirror the arm for opposite side. Rod used https://www.amazon.com/gp/product/B07KY9578R Category: R/C Vehicles
Xmod Gen2 Car Evo Front Upper Suspension Support Stock Height Stock replacement Category: R/C Vehicles
Xmod 1999 Nissan Skyline GTR R34 Front Clip Category: R/C Vehicles
Xmod 2004 Ford Mustang Cobra Front Clip Category: R/C Vehicles
This is an extended Gen1 chassis to make custom hardbodies fit xmods chassis. Use the body jig (sized to a standard chassis not the extended) and body clips to make the new body meet the old chassis. You can find the rear clip and many…
Remix of xmod rim, added room for center shaft, slightly bigger. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
This is a battery tray and clip to hold 2 single cell 10440 Lipo cells. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: No Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Xmod RC car steering rack. Gen1 Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Xmod 1967 Chevrolet Camaro Front Clip Category: R/C Vehicles
This is a work in progress, untested but measured correctly Xmod RC Truck Tires Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .15 Infill: 100 Filament: overture tpu black Category: R/C Vehicles
Xmod Gen2 Car Evo Rear Upper Suspension Support Stock Height Stock replacement Category: R/C Vehicles
Xmod steering rack Gen1 Category: R/C Vehicles
Xmod 2004 Mitsubishi Lancer Front Clip Changelog: V2: corrected the body stop Category: R/C Vehicles
Xmod RC front clip for a 2000 Honda Civic Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: generic pla Category: R/C Vehicles
Rear Control arms for Xmod RC Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Xmod 2004 Nissan 350Z Front Clip Category: R/C Vehicles
Rear clip that attaches to the chassis using the 2 pin style clips This is the rear clip that comes on the Red chassis (short wheel base), this has been recreated so that you can use the red body style clip on the yellow chassis (long…
Front blank plastic part that holds the front axle bearing and front shafts in place when in 2wd mode. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category:…
Xmod 2008 Chevrolet Corvette C6 Z06 Front Clip Category: R/C Vehicles
Xmods Evo Axle Shaft Bearing Thing (cars) GEN2 Stock: 9mm extended: 10mm extendeder: 11mm heat up a axle stub and shove it in, it will be as strong as stock Category: R/C Vehicles
Xmod 2000 Honda Civic Front Clip Category: R/C Vehicles
Xmod Trukin lowering kit brackets for the Truck line of Xmods Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100% Filament: generic pla+ n/a Category: R/C Vehicles
This is an extended Gen1 chassis to make custom hardbodies fit xmods chassis. Use the body jig (sized to a standard chassis not the extended) and body clips to make the new body meet the old chassis. You can find the rear clip and many…
Xmod 2004 Subaru Impreza WRX STI Front Clip Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .20 Infill: 20% Filament: generic PLA N/A Category: R/C Vehicles
This is a jig to turn any body into a xmod body. I believe the sizing is spot on, if you wanted to add it to a 3d model and print it all as one part. If not, print it on its own and glue it in! Category: R/C Vehicles
Xmod RC front clip for a 2003 Acura RSX Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: generic pla Category: R/C Vehicles
Xmod RC front clip for a 2003 Chevrolet Corvette C5 Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: generic pla Category: R/C Vehicles
Rear mount for upper control arm for Xmod RC car. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Front bearing holder for Xmod Rc cars Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
This is a steering servo stand off. Used when converting the electronics on an XMOD to hobby grade, but keeping the stock servo (using a 5 to 3 wire mod). It allows you to mount the servo and rear motor mount but opens up the room inside.…
This is an adapter for Hexmod RC cars to adapt to the Xmods Acura NSX body. Front: https://www.thingiverse.com/thing:5154465 Rear: https://www.thingiverse.com/thing:5154463 Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No…
Xmod RC front clip for a 2005 mustang Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 20 Filament: generic PLA Category: R/C Vehicles
Das ist ein Modell für die Hinterachse Aufhängung für den Xmod Truck F150 Für die andere Seite muß man es Spiegeln.
Hello, and welcome! My name is Sebastian, and I'm a Freshman at Suncoast Community Highschool in Florida. xMOD's mission is to offer an essentially upgradable house, where you can start with the barebones and work your way up. All the…
Xmod 2009 Nissan 370Z Front Clip Category: R/C Vehicles
Xmod 1965 Ford Mustang Front Clip Category: R/C Vehicles
Xmod 2005 Infiniti G35 Front Clip Category: R/C Vehicles
Xmods Trukin Axle Shaft Bearing Thing (Trucks) GEN2 Standard length and Extended length Will need the metal wheel mounting stub from an existing axle, Heat it up and it will slide in without any issues. Print Settings Printer Brand: Prusa…
Hexmod Yellow Front Clip (long chassis) Category: R/C Vehicles
Xmod Ford truck Bull Bumper Guard Modeled after the GPM bumper guard. For the mount, mirror to get both sides. Category: R/C Vehicles
Xmod RC front clip for a 1997 Toyota Supra Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: generic pla Category: R/C Vehicles
Body lock for Xmod Rear Chassis. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: .2 Infill: 100 Filament: generic PLA Category: R/C Vehicles
Many thanks to Rolohaun for a great design on the 2026 Mk2. Great little printer with a low barrier to entry and easy to build. This was a simple mod and works with the skirt inserts. This was made with TinkerCAD ... Lets see what you can…
Acme style Lipo holder for Xmod truck chassis. Category: R/C Vehicles
Xmod 2008 Nissan GTR Front Clip Category: R/C Vehicles
Xmod Bumblebee (2009 Chevrolet Camaro Concept) Front Clip Category: R/C Vehicles
Xmod 1967 Pontiac Firebird Front Clip Category: R/C Vehicles
Xmod 2009 Dodge Challenger SRT Front Clip Category: R/C Vehicles
Xmod 2006 Scion TC Front Clip Category: R/C Vehicles
body mount rear clip for the F150 truck xmod Category: R/C Vehicles
Xmod 2006 BMW 320si Front Clip Changelog: V2: fixed weak point on rear of clip Category: R/C Vehicles
Xmod 2003 Porsche Cayenne Turbo Front Clip Category: R/C Vehicles
Xmod 2003 Acura RSX Front Clip Category: R/C Vehicles
Xmod 2010 Ford Mustang Front Clip Category: R/C Vehicles
Xmod RC front clip for a 2004 Acura NSX Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: generic pla Category: R/C Vehicles
Xmod RC front clip for a 2008 Audi R8 Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: generic pla Category: R/C Vehicles
Front Knuckles for Xmod RC Trucks. Mirror the hub for opposite side. I printed them back side down with supports to get the cleanest results on the hub for the bearings. Category: R/C Vehicles
body mount rear clip for the F150 truck xmod. it has been extended to allow for a lifted look. Take the front clip, flip it upside down, add this part and you get a lifted f150. Category: R/C Vehicles
Xmod 2005 Ford F-150 Front Clip Category: R/C Vehicles
Xmod 2004 Mercedes-Benz SLR McLaren Front Clip Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: .2 Infill: 100% Filament: generic pla+ n/a Category: R/C Vehicles
This is an adapter for Hexmod RC cars to adapt to the Xmods Acura RSX body. Front: https://www.thingiverse.com/thing:5153568 Rear: https://www.thingiverse.com/thing:5154031 Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No…
