1 / 3
Leaf Grabber Mod for DARLAC Grab-N-Lift DP556 15deg angle and slightly longer. — image 1
1 / 3

Leaf Grabber Mod for DARLAC Grab-N-Lift DP556 15deg angle and slightly longer.

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Modifies the leaf grabber to angle the grabbers better and lengthens slightly especially for taller people.

Rating
0 / 5
Likes
0
Downloads
8
Makes
0
Views
89
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

It used to be possible to buy leaf grabbers that were slightly angled at the head (I think Gardman made them, but they've changed the design). That way you could pick up leaves that were a little further in front of you rather than right at your feet. Also, in common with just about every other garden device on the market, they're JUST too short for anyone around 6 feet tall which is really annoying and bad for the back!

This mod deals with both issues. It changes the angle of the scoops from straight to 15deg and extends them about 10cm, so you tilt the handles slightly to keep the bottom of the scoops level with the ground - that requires a little more effort with the hands but less bending over. 

The existing bolts are a bit silly - hex heads fitted in countersunk holes so you can only just get at the head to hold it with pliers and undo the nut with a spanner or another pliers. I found that a countersunk M5x40mm crosshead bolt fitted the existing countersunk scoop hole nicely and I had them in stock so I designed the print to match.

Parts needed - 4 of M5x40mm crosshead bolts, 2 of M5 locking nuts, 2 of M5 plain washers

You can reuse the 2 existing locking nuts and washers with the mod. You can also use the two hex head bolts instead of 2 of the crosshead bolts if you like but the crossheads are much easier to use!

I trimmed the bolts to length with a hacksaw and file just for neatness - the originals just stuck out like they couldn't be bothered to specify the right length :o)

Print Settings:

Material - I only have PLA+ and that seems fine but don't leave it out in the Sun! Use anything stronger if you like.

Layer Height 0.2mm but anything sensible for your printer should be fine

Nozzle Diameter - I only have 0.4mm available so that's what I used

Walls - UPDATED - after an “incident” I reprinted with 8 walls. The joint between the two tubes needs to be STRONG!

Infill - UPDATED - after the “incident” I switched to 70% triangular infill for better strength

Adhesion - I used a 3-line brim just for a bit of confidence, my PEI bed sticks well but this is quite a tall narrow model  

Orientation - Open end of the larger tube should be flat on the printbed, so I've orientated it like that in the STL file

Building: Remove the two nuts on the scoop bolts, grabbing the buried hex bolt heads as best you can. The scoops are quite tight so rotate them back and forth as you ease them off. Arrange the printed parts so the bend is in the same direction as the hand grips, and bolt it all together again. The part of the print that fits in the scoop section is quite a good fit - because the scoops are plastic and have a bit of give. The part of the print that slides over the handle tubing is slightly looser because that's metal and won't give if it's too tight, add a bit of insulating tape to the metal tube if you want it more snug but it shouldn't matter unless yours turns out particularly loose. I didn't want to have to reprint cos each part takes about 6 hours on my printer!

Hope this makes leaf collecting time a little easier for you. Don't leave PLA out in the Sun, especially if you do it in a dark colour, or it might soften and bend or snap. Fortunately leaves tend to fall in the Autumn when the Sun isn't as hot anyway.

Please Like this model if you find it useful.

If you REALLY like it, https://www.buymeacoffee.com/gigabeast :o)

Tags