1 / 45
AXIAL SCX10 I & II - Chassis Parts / Update 22.10.2026 - New Body Mounts — image 1
1 / 45

AXIAL SCX10 I & II - Chassis Parts / Update 22.10.2026 - New Body Mounts

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A few useful parts for the good old SCX10 I&II. Read the description.

Rating
0 / 5
Likes
53
Downloads
411
Makes
0
Views
1,582
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution

Description General

  • I have collected all SCX10 I & II parts i published on Printables so far.

  • The chassis rails and skid of the SCX10 I are absolutely identical to those of the SCX10 II. So, many parts are suitable for both chassis.

  • Attention: With a wheelbase of 313mm, Gen1 and Gen2 differ significantly in link lengths. Gen1 has the same length front and rear. Gen2 has a short in the front and a long in the rear. Bodymount for Gen1 dont work with Gen2! With a wheelbase of 290mm, the generations are identical again.

  • The link mounts on the Gen2 AR44 axels put the links 1.5-2mm closer to the axle housing than the old Gen1 axles. So If you use Gen1 links with Gen2 axes, these must be extended.

  • L and R mean left and right. Most parts are available for both sides; if not, they must be mirrored in the slicer.

  • All parts are designed to be stable even in PLA. 15% infill and 3 wall lines.

  • For each part there is a photo showing how it is assembled.

Description WIDE chassis

  • The distance between chassis rails is 7.6mm more than on the original SCX10.

  • Optimized for servo on the axle; with the original, the servo sometimes touched the frame.

  • All original parts located between the rails are not compatible with this.

  • All parts specifically designed for the wide chassis are labelled WIDE.

Description Parts

Skidplate for TRX4 Gearbox

  • This allows you to use the TRX-4 two-speed transmission on the SCX10 Gen1&2.

  • Works with 4-link (servo on axle) or 3-link panhard. 

  • Portal axels are needed (reduction), straight axels become far too fast.

  • I used a clone gearbox from far east with MEUS portal axles. A great, inexpensive combo that's excellent for both crawling and bashing.

  • Connect all parts with M3 screws; these are screwed directly into the plastic.

Skidplate Gen1&2

  • Some simplified versions of the SCX10I skid plate.

  • More mounting positions than the original.

  • Optimized for different pivot ball sizes.

3 Gear Transmission Spacer

  • This spacer fits the AXIAL SCX10 3 Gear Transmission hole pattern, which was installed on the SCX10I and II. 

  • Element RC Stealth X and Vanquish VS4-10 3 Gear Skid also fit.

  • Versions with a distance of 2mm, 3mm, 4mm, 5mm and 6mm are available.

Shocktower Gen1

  • Shocktower based on those of the first generation.

  • Without Panhard mount.

  • Designed for 90mm shock absorbers.

Shocktower Gen2

  • SCX10II shock towers with Panhard (variant without panhard is also included)

  • They have a backplate so that they have the stability of original parts when 3D printed.

  • No original parts fit between the towers because of the backplate.

  • I use the all_in_one_front_2.0 for the battery and servo.

Bumper Mount 

  • Classic bumper brackets for front and rear.

  • It's best to print with high infill or strong materials.

Bumper Mount  - All in One

  • A combination servo and pump holder including compartment for battery and electronics.

  • all_in_one_front_2.0 only works with my self-developed shock towers.

  • For variants where the servo is located in the middle, the drag link/tie rod may need to be adjusted (shorter rod ends). The offset version matches the original axial geometry 100%.

  • Can be extendet for mor space (only with stubby motor).

  • There is a version for classic bumper mounting and versions without tubes and the bumpers are screwed in directly.

Bumper Mount  - Spacer

  • For the bumper brackets that are screwed on directly, a few spacers are needed to adjust the distance precisely.

Universal Side Plate / Electronic Plate / Floor Pans

  • Space for electronics or batteries

  • The new version is designed for scale crawlers with small wheels. Large wheels (over 110mm) could rub when turning.

SCX10I with SCX10II Body - Magnetic Body Mounts / Adjustable Offset

  • SCX10II body does not fit directly onto an SCX10I (different hole pattern). Here is the solution. 

  • The PostStands from the SCX10I and II have a different hole pattern. SCX10I with 56mm to SCX10II with 72mm. 

  • That's why I developed these adapters, with a magnetic function, to put my SCX10II body on my aging grandpa.

  • Requires  8 neody magnets (15x3mm with hole for countersunk screw), you can get them on Amazon.

  • If the holes are offset from front to back, there are two holder versions with different offset sizes.

  • If no PostStands are available, I have included the print file for them.

  • In order to attach the magnets to the body, I have stored a file for a washer into an M3 nut can be pressed.

Team Raffee / Injora Jeep Cherokee XJ & Comanche Body Mounts (Gen2)

  • Requires my universal_gen1&2 Side Plate.

  • Wheelbase 313mm / 12,3", SCX10Gen2 out of the box, SCX10Gen1 links need to be adjusted.

  • Must be glued as shown in picture so that the wheelbase fits.

  • Intended for firmly screwed installation. M3 threads must be cut into the holders. M3 holes must be drilled through the side plates.

  • Use M3 x 18mm screws.

  • For the other side, mirror in the slicer.

Team Raffee / Injora Jeep Cherokee XJ & Comanche Body Mounts (Gen2) V2 / Magnetic Mount

  • Requires my universal_V2_40mm Side Plate.

  • It's compatible with my Comanche interior. It serves as a base.

  • Designed as a magnetic mount, no tools required.

  • 15x3mm neodymium magnets are required.

  • Must be glued to the body as shown in picture.

  • Front and rear mounts are optional. Require my custom-designed shock tower and bumper mounts.

Jeep JK Body Mounts (Gen2) - Magnetic Mount

  • Requires my SCX10II front shock tower & universal_V2_40mm Side Plate..

  • Refer to the photos for assembly instructions.

  • 15x3mm neodymium magnets hold the body very firmly.

Team Raffee Land Rover Discovery 1. Gen Body Mounts (Gen2)

  • Remove the original body sliders. The new floorboards/body mounts will go in these locations.

  • Drill 2.5mm holes through the mounting point into the body. Now screw M3 screws directly into the plastic of the body.

  • Take a look at the photos.