1 / 7
Spiffy 35mm film roll splitter with frame counter — image 1
1 / 7

Spiffy 35mm film roll splitter with frame counter

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A gadget that allows you to easily transfer film from one 35mm canister to another, with a frame counter.

Rating
5 / 5
Likes
32
Downloads
231
Makes
4
Views
1,155
Reviews
1

Updated at source:

Model information

License
Creative Commons — Attribution

This is a cool little gadget that allows you to easily transfer film from a film canister to an empty canister. There are others out there, but this one counts your frames too!

Splitting rolls is commonly done when you want to do experimentation and don't want to waste full 36-frame rolls. With the release of the Pentax 17 half-frame camera, this film splitter gadget is even more useful, as the Pentax 17 shoots 72 frames per full roll--who has that many ideas at one time?

This model does not include the 35mm film rewind knob--there already is a perfect one designed by Loender, so I didn't want to redesign it.

https://www.printables.com/model/564341-manual-35mm-film-rewind-knob

Print the knob with 100% infill so that the forks are solid.

The film splitter is fairly simple to print and assemble. Everything should lay nicely on the build surface. Place the sprocket with the wide end on the build surface.

You should be able to print these parts without any supports and without the need for brim.

Once you are done, use an appropriate sized drill bit to clean out the center hole by hand. Just grab a drill that feels slightly snug but you can use by hand to ream out the hole.

Use a hobby knife to clean up any burs on the shaft of the sprocket so it can spin freely in the center hole.

Use a 1/16" drill bit to clean out the tiny hole in the end of the sprocket shaft--once it is clean you ought to be able to insert a short piece of bright filament and then cut it off flush with a hobby knife. No glue needed.

If you wish, you can glue in the plug that holds the sprocket in place. I didn't bother, it stays in on its own.

As always, I have included the FreeCAD file with a spreadsheet that controls most of the fiddly settings. Sorry about the imperial units, just type “mm” instead of “in” for your changes and it will calculate everything correctly.

Usage

Cut the shaped leader off of the donor roll as close to the end as possible. Use tape to connect that to an empty canister. Place both in the device. I usually insert the empty canister with pointy-bit facing up.

Place the lid on, taking care to ensure that the two ramp-shaped prongs in the lid slide behind the film, pressing it against the sprocket teeth.

Now insert the winder key in the empty canister's end and turn in the direction of the arrow.

Count a half frame (half of a rotation of the dot), then count 20 full frames.

Open the device, use your finger to pull the film away from the sprocket, and withdraw the canisters. Snip in the center, give each film a 45-degree clip on the end, and label them. You're all done!

By counting 20 frames, if you are stingy while loading your camera, you ought to get 16 frames from one roll and 17 frames from the other. Double that if you are using the Pentax 17!

License

This model was originally released under the Creative Commons Attribution–NonCommercial 4.0 International (CC BY-NC 4.0) license.
It is now shared under the Creative Commons Attribution 4.0 International (CC BY 4.0) license, which permits commercial use provided proper credit is given to the original designer.

If you manufacture or sell this model, please include attribution such as:

Design by Tad Harrison — [link to this Printables page]
Licensed under Creative Commons Attribution 4.0 International License

Re-uploads of the STL or source files to other platforms are not permitted; please link back to this original page instead.

Tags