Anti-Rattle Bushings for Ender3 V3 KE/SE Y-Axis Linear Rods
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Custom bushings that keep the linear rods from moving up and down in the front of the Ender3 V3 KE/SE base housing.
- Rating
- 0 / 5
- Likes
- 59
- Downloads
- 201
- Makes
- 0
- Views
- 1,774
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Creality Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial
The Ender3 V3 KE used to have two screws in the front that would hold down the linear rods in the base housing. Recently, there was a design change and Creality eliminated those screws (they were also too short). Now, on some production batches (not all), there is about 0.3mm play in the up and down direction, on the front end of the two rods.
Normally not a big problem but on certain taller prints, if there is enough nozzle drag and inertia at play that lifts the rods up causing a rattle and loss in print quality.
Most people convert the y-axis to linear rails to eliminate this problem. I've done plenty of these conversions over the years on other printers, but still:
I'm in a print farm setting and in my opinion, this expense and extra work is not necessary if the root cause can be eliminated.
To do exactly that, I designed these half shell bushings to eliminate this play (at zero cost).
Installation takes only a few minutes.
There are several sizes of the bushing provided. The number in the end indicates how thick the bushing is at its center. This correlates to the amount of play you have going on, if you measured it. I designed these against two brand new printers and the 0.28mm version worked just fine and zeroed out the play completely.
My assumption is that if you run the KE for a while without these bushings, it will get worse. So, I'm providing a few variations, just in case:
E3V3KE-Anti-Rattle-Bushing-0.28mm (Worked for me, start here)
E3V3KE-Anti-Rattle-Bushing-0.30mm (If there's still play, go one size up)
E3V3KE-Anti-Rattle-Bushing-0.32mm (If there's still play, go one size up)
E3V3KE-Anti-Rattle-Bushing-0.34mm (If there's still play, go one size up)
E3V3KE-Anti-Rattle-Bushing-0.36mm (If there's still play, send me a message)
If any of these keep breaking during install or it gets too tight, go down one size.
Profile settings:
This part requires a 0.2mm nozzle, it will likely not work very well with a standard 0.4 nozzle!
Nozzle Size: 0.2
Line Width: 0.2mm
Layer Height: 0.12mm
Wall Loops: 5
Top and bottom shell layers: 3
The footprint is very small and if you can't get it to stick, add a brim:
Outer and Inner, 2mm width, brim/object gap: 0.04mm
Material:
You can print this in PLA, but I found the tiny shim gets too brittle and will break apart easily during installation.
My preference was Hatchbox Black PETG, but any PETG will do:
You want as much strength as possible in this little bushing. With 0.2mm nozzles in general, you want to print about 10C hotter than you normally would to avoid clogging and also to make the layers adhere better to each other. I went for the max at 260C and only 60% cooling for PETG. I also found that printing PETG this hot, causes excessive stringing - so I printed one piece at a time to avoid that.
Tip: If you only have one printer, print a whole bunch of these before you begin installation. These things are fragile and tend to break until you have the installation process down.
Installation:
- Remove the two screws in the back of the printer holding the two rods in place.
Warning: Be careful from here, if the rods slide all the way out of the bearings, some of the little bearing balls might fall out and that would be catastrophic.
- Slide the rods forward a little bit until they clear the hole in the back.
- Lift the back of the rods up and slide them back and over the base by just a little bit until they clear the hole in the front.
- Set the bushing on top of the end of the rod and carefully slide them back into the hole in the front. It works best if the bushing tongue enters the hole first and then slides in with the rod.
- Drop the back end of the rods back into the little cradle.
- Now hold the bushing itself in place with one hand and slide the rod backwards with your other hand, back into the hole in the back.
- Check if the play has been eliminated. If there is still play, go one size up.
- Put the two screws at the rear end of the rods back in place.
- If you're paranoid about this, you could even epoxy the colar to the base at this point, but I didn't go that far.
You're done! :-) Hopefully there is zero play on both sides at this point.
Alternative hack:
If you can't get this to print correctly at all (it's a little challenging) or it keeps breaking on you during the installation, there is an alternative (the installation procedure is the exact same). Find a durable material that is about 0.3mm in thickness, or however much play you have if you measured it.
On a brand new one, 0.3mm is what I measured.
Standard shrink tubing happens to be about exactly that thick. During prototyping, I cut a little square piece about 40% of the circumference of the rod and perhaps 15mm long. Roll it up a little and feed it into the hole along with the rod. A little bit of a hack, but it should work too - alternatively.
Good Luck
Mac@Ka3d