1 / 8
FREE DIY Pumpkin scarer (it drops something scary on trickortreater's hand as they get candy) — image 1
1 / 8

FREE DIY Pumpkin scarer (it drops something scary on trickortreater's hand as they get candy)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

(Motion detected) This design drops a scary thing of your choice(in my case it is a hand or 3d printed spiders)

Rating
0 / 5
Likes
3
Downloads
6
Makes
0
Views
208
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution — Noncommercial

bdw you can put this anywhere to scare someone

READ WHOLE DESCRIPTION!

Connections to Arduino Uno are down below.

Video for people who do not know how to wire Arduino or set up electronics on the pumpkin : https://youtu.be/M4WuB30qgcw

WHAT IT DOES:

These files drop something scary when it detect your hand going inside the pumpkin, leading to tricktreaters getting SPOOKED

i made this because this year i am not going trick-treating, so i decided to make a design that will "hopefully" scare everyone who comes to our door so i can eat all our leftover candy lol

FILES TO PRINT: Choose what you want to drop and print accordingly. The files saying spider are for many small stuff; the files saying hand are for one big thing. ALL FILES SAYING NEEDED ARE NEEDED REGARDLESS

TIME:

The NEEDED take about 5 hours to print on Ender 3 Pro, but you can save half that time if you print the main big box in vase mode by checking the "spiralize outer contour" box in cura. ONLY THE MAIN ELECTRONIC BOX CAN BE PRINTED IN VASE MODE; however, there will be some irregularities and it will be weaker but if you are doing this for only one year, then it should be fine.

Arduino: i know i am using an arduino Uno, and it is bigger but that is all i had If you want to edit it for an Arduino, I can give the fusion 360 files :)

Connections: servo GND TO GND, servo Positive to 5v, servo signal to port 9 on arduino, signal pin of Pir sensor to port 2 on arduino,

Sensor gnd to GND, Sensor positive to Arduino 5v

Part list, their are cheaper ones online. This is just for refrence (i am using a smraza arduino kit)

 Sensor : https://a.co/d/15jF96J

Servo : https://a.co/d/0YDQVT7

Arduino uno : https://a.co/d/0qqMdYq

Jumper wires : https://a.co/d/aGqkviH

and usb for uploading code usually comes with the arduino


 

CODE :

#include <Servo.h>

Servo myServo; // Create a servo object

int servoPin = 9; // Servo connected to pin 9

int pirPin = 2; // PIR sensor connected to pin 2

int pirState = LOW; // Variable to store PIR state

int motionDetected = 0; // Variable for motion status

void setup() {

  myServo.attach(servoPin); // Attach the servo to the pin

  pinMode(pirPin, INPUT); // Set PIR pin as input

  myServo.write(0); // Set initial servo position to 0 degrees

  Serial.begin(9600); // Start serial communication for debugging

}

void loop() {

  motionDetected = digitalRead(pirPin); // Read PIR sensor

  if (motionDetected == HIGH) { // If motion is detected

    if (pirState == LOW) {

      Serial.println("Motion detected!");

      myServo.write(90); // Move servo to 90 degrees

      pirState = HIGH;

    }

  } else {

    if (pirState == HIGH) {

      Serial.println("Motion ended!");

      myServo.write(0); // Move servo back to 0 degrees

      pirState = LOW;

    }

  }

}

SETTINGS

i printed with 20% infill

no vase mode and prints with 0.2 mm quality

You can print ONLY the main electronics box in vase mode (checking the "spirilize outer contour" in cura); however, it will be much weaker.

 

ASSEMBLY

Put your Arduino in the main electronic box and make sure that your power plug is line up with the circular hole.

glue your servo in to the rectangular hole on the main electronic box and wire your electronic according to the diagram.

Then wire your sensor and then put it in to the sensor box and glue it on the outside plastic part a little Glue some of the wires too a little to secure them MAKE SURE TO EXTEND THEM FIRST THOUGH. 

Then wire your sensor to Arduino, taking the wires in from the small gap in the bottom of the servo hole making sure you do not interfere with the servo horn.

Then you put the sensor where ever you eant but i put it over the top of the mouth and covered areas where i do not want it to see with tape.

Then tape or glue the main box on top of your pumpkin stock, where you probably cut to take out the inside stuff.

then make a hole through the top to let the string pass through the stock easy and tie your string to the file "ring for the string."

this is for hooking your string to the servo for release mechanism.

and tape the end of your extra string to the electronics box so it is easy to reset your trap lol

Share your prints! :)

(ps i would love to see somone put real bugs in )


 

Tags