Super Dust Deputy 4/5 Top Adapter 6" to 5" - turn Harbor Freight 2HP DC into 2-Stage, using Super Dust Deputy 4/5
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Converts 6" on top of Super Dust Deputy to 5" on Harbor Freight 2HP Dust Collector's blower inlet. Also see related part
- Rating
- 0 / 5
- Likes
- 19
- Downloads
- 76
- Makes
- 0
- Views
- 651
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Tools
- License
- Creative Commons — Attribution — Noncommercial





Ok, so I mocked up my stock, store-bought Harbor Freight 2HP dust collector, so I could plan for rearranging its parts to make my setup 2-stage instead of 1-stage.
In these screen shots below, the plan for the new setup is on the left, and the stock setup is on the right. I set them side by side so the stock setup could be compared with the re-arranged version.



In the stock configuration, the stock hose (marked in salmon color / pink color) is a factory 5" diameter hose. By cutting two portions off, one about 4" to 5" in length and another slightly shorter than 6" in length, I will be able to connect the “*Super Dust Deputy 4/5” to the blower motor, coming from the 3D printed adapter marked in green, going from 6" down to 5" inlet on the blower / impeller area, and will also be able to connect the stock, factory 5" air outlet on the blower motor, marked in blue, to the 5" air inlet on the separator ring. The white cylinder on top the separator ring represents either the factory bag filter or my pleated canister filter. The empty area under the separator ring would either have the factory plastic bag, or in my case, my trashcan that attaches to a DIY quick-connect MDF ring feature that I had previously modeled and made.
The model currently does not show the casters on the base, but I have the base floating about how high it is on the stock casters.
The basic idea is that I will build a wooden box, attach it to the base, and attach the support rods that hold the separator ring, thus elevating the separator ring to the new higher location. This will also nudge the separator ring closer to the end of the base, allowing room for the new galvanized steel trashcan my “*Super Dust Deputy 4/5” is attached to.

IMPORTANT NOTE
If you look in the drawings/3-D modeling renders you’ll see there is a gap between the printed part and the impeller — I connected them with a piece of the stock hose that came with the dust collector — shown in the screen renderings as a salmon colored hose, and in reality it was a dark gray colored hose. This printed part was meant to be connected to a hose that is connected to the dust collector impeller, not meant to be connected directly to the impeller itself. I mentioned this above but it was not made clear enough. If you want to connect them directly to each other, without any hose there, then it would require a remix of this part.
Print notes
- Print as oriented
- No supports needed
- I printed with PLA
- I printed with 0.28 layer height, on a 0.4 mm nozzle.
- Prints faster when you up the number of perimeter walls so the cylinder portions print solid and you don't have to bother with infill except for a small area where the thickness increases.
FAQ
- Q: Why not just use the adapter supplied with the Super Dust Deputy?
- A: It would reduce the size to 4" diameter. Larger is better. No adapter is 6" for the outlet on top. Their supplied adapter can either take a 5" to a 4" (on inlet), or take a 6" to a 4" (on outlet).
Also see (below) my related models used in my conversion from 1-stage to 2-stage on my dust collection:
Dust Collection Adapter (from Harbor Freight 2HP DC 2-into-1 "Y" to Super Dust Deputy 4/5's inlet port — 5" to 5" - https://www.printables.com/model/1071489-dust-collection-adapter-from-harbor-freight-2hp-dc

Dust Splice Coupler Adapter - from 4" PVC to 4" Dust Hose (based on POWERTEC 70123 O.D. Splice, 4", Black) - https://www.printables.com/model/1077981-dust-splice-coupler-adapter-from-4-pvc-to-4-dust-h

Dust Splice Coupler Adapter - from 4" Flex Hose to 4" Flex Hose - https://www.printables.com/model/1077997-dust-splice-coupler-adapter-from-4-flex-hose-to-4

Harbor Freight 2HP Dust Collector outlet port with downward curve (or flip it for upward curve) v1.0 - https://www.printables.com/model/1087419-harbor-freight-2hp-dust-collector-outlet-port-with

*Amazon links are affiliate links.