1 / 6
Kobalt 24V Li-Ion battery adapter for Pinecil/TS100 soldering iron — image 1
1 / 6

Kobalt 24V Li-Ion battery adapter for Pinecil/TS100 soldering iron

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This adapter converts a Kobalt tool battery into a portable soldering station for a Pinecil or TS100 iron.

Rating
0 / 5
Likes
19
Downloads
40
Makes
0
Views
429
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution

Design Intent

This adapter includes under-voltage protection. Rechargeable lithium ion batteries can be severely damaged or completely destroyed if allowed to discharge too low. Kobalt tools have internal electronics that signal the battery to disconnect from the tool when the charge falls below a given voltage. It is very easy to ruin these batteries if used to power non-Kobalt accessories without any protection. This adapter allows you to use Kobalt batteries to safely power a Pinecil/TS100 soldering iron but it can also be used to power any accessory that can run on 24V DC.

Filament and settings used for this project

  • Spectrum Smart ABS - Pacific Blue
  • Polymaker Polylite ABS - Black
  • 0.4mm nozzle, 0.2mm layer height, 20% infill

Bill Of Materials

You will need additional items to assemble this adapter. Please note that the source links are provided for reference only. They might not be the best possible source for you.

Hardware
QuantityDescriptionSource
14M3x5x4mm heat set insertsAmazon
4M3x6 Button Head Cap Screws (BHCS)Amazon
2M3x8 Button Head Cap Screws (BHCS)Amazon
2M3 Nylock nutsAmazon
4M3x6 Socket Head Cap Screws (SHCS)Amazon
2M3x10 Socket Head Cap Screws (SHCS)Amazon
4M3x20 Socket Head Cap Screws (SHCS)Amazon
70mm10mm O.D. Aluminum tubeAmazon
70mm10mm I.D. Silicone tubingAmazon

 

Electronics
QuantityDescriptionSource
214-16AWG (Blue insulation) 0.250" width spade terminalsAmazon
416AWG (Black insulation) ferrulesAmazon
1SPST Rocker switch (may include 16AWG wires)Amazon
400mm16AWG 2-Conductor Silicone wire (if not included with switch)Amazon
1ATC/ATO Fuse holderAmazon
15A ATC/ATO FuseAmazon
2Red Anderson Powerpole connector housingsAmazon
2Black Anderson Powerpole connector housingsAmazon
4Anderson Powerpole 15A crimp terminalsAmazon
1Power cable semi assembled w/DC5525 power plugAmazon
1Programmable XH-M609 Low Voltage Disconnect ModuleAmazon

 

Assembly

The assembly and wiring steps of this adapter are similar to the ones for my Milwaukee Tools M18 Li-Ion battery adapter for Pinecil/TS100 soldering iron design. There are only a few differences:

  • M3x10 SCHS  are used instead of M3x16 SHCS to fasten the top part of the adapter to the bottom part.
  • M3x20 SHCS are used instead of M3x25 SHCS to fasten the iron stand to the adapter assembly.
  • Wires are cut to a different length.

Details to look out for

  • The spade terminal contact block is integral to the top part of the adapter instead of being made from 2 separate halves like the one on my Milwaukee and DeWalt adapters. This should help make wiring simpler.

 

  •  Be aware that depending on your printer and the filament used, the fit for the terminals and/or wires can be a little tight. If you're experiencing difficulty pushing the barrel of the spade terminals or the wires through the holes, you can enlarge them using the tip of a 3mm hex driver or Allen wrench.

 

  • It is recommended that you fasten the barrels of the spade terminals to the contact block with a drop of CA glue during final assembly. This will prevent them from being pulled out of the contact block when unplugging the adapter from the battery.

Wiring

  • Due to the particular geometry of the Kobalt battery, the top half of this adapter is a bit shallower than the one on the Milwaukee adapter so the power switch leads end up being too close to the component leads sticking out from the bottom of the PCB. To prevent shorting the circuit or the battery, a few extra steps are required.
  1. Trim the leads on the bottom of the PCB before you mount it into the adapter.
  2. Bend the power switch leads sideways after soldering the wires onto it.

1.

2.

WARNING!!

It is absolutely essential that you perform the above steps. If you fail to do this, you could potentially fry the circuit board AND/OR damage your battery.

Cut 6 lengths of 16AWG wire
Red: 40mm, 65mm, 70mm, 80mmBlack: 80mm, 100mm
  • Make connections as shown in the table and the picture below:
Wire color & lengthTermination Side ATermination Side B
40mm RedPowerpole terminal +Soldered to fuse lead out
65mm RedFerrule to Vout+Soldered to fuse lead in
70mm RedFerrule to Vin+Soldered to switch lead out
80mm RedSpade terminal +Soldered to switch lead in
80mm BlackPowerpole terminal -Ferrule to Vout-
100mm BlackSpade terminal -Ferrule to Vin-

 

Tags