1 / 4
Topton N100 Stand with top and bottom fans 124x138 — image 1
1 / 4

Topton N100 Stand with top and bottom fans 124x138

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a three-part print that lets you mount an 80mm fan below, and a 120mm fan above, your new Topton N100…

Rating
0 / 5
Likes
1
Downloads
20
Makes
0
Views
367
Reviews
0

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial

This is a three-part print that lets you mount an 80mm fan below, and a 120mm fan above, your new Topton N100 "fanless" pc that you just bought only to discover that it overheats and/or burns your fingers.

If you haven't bought one of these yet, please... don't. If (like me) you're already stuck with it and have to make it work, this print should help.

When I first received this pc/waffle cooker, it would only run for 30 seconds before overheating and shutting down. I opened it up to discover the most idiotic, incompetent thermal design I've ever seen. The bottom cover has vent slots, but there are no holes anywhere else in the case, so there won't be any airflow.

I also found a thermal-grease-smeared chunk of copper bouncing around inside, nowhere near the CPU it was supposed to cool, which had an even more impressive glob of thermal goop all over it.

After cleaning everything up, putting the copper block back where it belongs (indicated by a small relief in the upper case), and applying a normal amount of thermal compound, it was obvious that there was a huge gap (over half a mm) between the copper block and the CPU.

At this point, the unit would stay running, but the CPU temp was around 80, even with both fans at full speed. This wasn't a surprise... thermal compound is not intended to fill gaps like that.

I took about 0.3 mm off of the mounting studs with a flat file (make sure you don't leave any metal filings inside the case). That's pretty much the most you can take off and have the ports still fit through the cutouts in the front and rear panels. This helped, but only by about 10 degrees, and I could still see daylight between the cpu and the copper block.

So I added a 0.3mm copper shim to the copper block. This, plus this stand with both fans at full blast, plus replacing all the thermal compound with MX-6, finally brought the temp down to around 30! Even reducing the fans to half-speed didn't cause the temperature to rise.

So of course, I had to try turning the fans off to see if maybe they weren't needed after all. I aborted the experiment at 50C (and still rising) because that's approaching the burn-your-fingers zone, and besides even if the CPU can survive whatever steady-state temperature it would have settled at, the NVME drive below it with no heatsink and no airflow could have its life significantly shortened.

I intended to print all of this in PETG to better withstand the heat, but I printed fit-check parts in PLA, and when against all odds they fit perfectly on the first try, I just decided to use them, knowing full well that if the fans ever quit, the whole stand will likely melt into a puddle of goo.

The upper fan support attaches to the stand using M2.5H4 heat-set inserts and M2.5x18 cap screws (x20 should fit too, I think). Nothing magic about these, it's just what I had on hand. The openscad files are included so you can change this if you want.

Thanks to Zer0s and rivado for the inspiration. I think Topton changed the dimensions of their cases recently, though, because these didn't quite fit my box, which for the record measures roughly 124x138 mm.

I also chose an 80mm and a 120mm fan grille from here to keep out fingers and/or paws.

Here are all the parts I used (not affiliate links):

Arctic MX-6
0.3 mm copper shims
heatset insert tool
heatset insert assortment
usb fan controller
metric screw assortment
120mm fan
80mm fan

Pasting notes:

When replacing the copper block, take note of the step milled into one side. It is there to clear another component, so be sure the edge with the step faces the middle of the board.

When applying the MX-6, I pasted the top of the block with a single line down the center of the long axis. I then put it into the slot in the case and squeezed as hard as I could to spread the paste, until I saw squeeze-out on all 4 edges. I then put a single dot on two copper shims, and squished them onto the block side-by-side in position to contact the two raised parts of the CPU, again squeezing as hard as possible to distribute the paste. I then put a dot on top of each CPU die and assembled the board (no squeezing here, didn't want to break anything).

Print Settings

Printer Brand:

Sovol 3D

Printer:

Sovol SV01

Rafts:

No

Supports:

No

Resolution:

0.2mm

Infill:

30%

Filament: Generic PLA Dark Blue Notes:

PETG would withstand the heat better, I think.

Category: Computer

Tags