Tesla - Jackpads for Model Y from 2023 with BYD battery
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
DIY Jackpads for Tesla Model Y from 2023 RWD 2023 with BYD-Battery
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 30
- Makes
- 0
- Views
- 472
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Automotive
- License
- Creative Commons — Attribution — Share Alike
Tesla - Jackpads for Model Y with BYD battery from 2023
To protect the vehicle battery, the Tesla Model Y requires so-called jackpads when using a jack or on a workshop lift. This is a hard rubber disk that is very similar to an ice hockey puck in shape, size and material. The jackpads are inserted into prepared holes in the underbody of the Tesla and thus protect the underbody / battery from damage when the vehicle is lifted.
With an ice hockey puck, a small 3D-printed “plug”, 2 screws and three small drilled holes, you can quickly make such a jackpad yourself. The center finder for the holes in the puck is also best printed out directly.
The diameter of the plug is 20.3 mm and therefore fits into the holes of the Model Y RWD with 60KW BYD battery. Dimensions for holes and screws can be found in the enclosed drawing.
It is recommended to use TPU/Flex filament (approx. 70% filling) for printing the connectors, as the pucks sit firmly in the holes, but can also be pulled out again without much effort.
The diameter of the plug can be easily adapted for other Tesla models using the FreeCAD or step file that is also available.
OK, the whole thing is perhaps a little “overengineered”, but it's fun and the workshop I trust is very happy with it! :-)
Material required for four jackpads (for lifting platforms):
4 ice hockey pucks
4 hexagon socket head screws M6 x 20mm
4 M6 x 12 tapping inserts with cover edge
Translation supported by DeepL
Tesla - Jackpads für Model Y mit BYD-Akku ab 2023
Zum Schutz des Fahrzeug-Akkus benötigt das Tesla Model Y bei Einsatz eines Wagenhebers oder auf einer Werkstatthebebühne sog. Jackpads. Dabei handelt es sich um eine Hartgummi-Scheibe, die sowohl in ihrer Form und Größe als auch ihrem Material sehr stark an einen Eishockeypuck erinnert. Die Jackpads werden in vorbereitete Bohrungen im Unterboden des Tesla gesteckt und schützen dadurch den Unterboden / Akku vor Beschädigungen beim Anheben des Fahrzeugs.
Mit einem Eishockeypuck, einem kleinen 3D-gedruckten "Stecker", 2 Schrauben und drei kleinen Bohrungen lässt sich ein solcher Jackpad schnell selbst herstellen. Auch den Mittenfinder für die Bohrungen in den Puck druckt man sich am besten direkt mit aus.
Der Durchmesser des Steckers beträgt 20,3 mm und passt damit in die Bohrungen des Model Y RWD mit 60KW BYD-Akku. Maße für Bohrungen und Schrauben ergeben sich aus der beigefügten Zeichnung.
Es empfiehlt sich, TPU/Flex-Filament (ca. 70% Füllung) für den Druck der Stecker zu benutzen, da die Pucks damit einerseits fest in den Bohrungen sitzen, jedoch auch wieder ohne großen Kraftaufwand herausgezogen werden können.
Über die ebenfalls vorhandene FreeCAD- oder Step-Datei lässt sich der Durchmesser des Steckers für andere Tesla-Modelle leicht anpassen.
OK, das ganze Ding ist vielleicht ein klein wenig "overengineerd", macht aber Spaß und die Werkstatt meines Vertrauens ist sehr damit zufrieden! :-)
Benötigtes Material für vier Jackpads (f. Hebebühnen):
4 Eishockeypucks
4 Zylinderkopfschrauben Innensechskant M6 x 20mm
4 Eindrehmuffen M6 x 12 mit Abdeckrand