1 / 6
608 Bearing and/or Vase Mode Spool for Scott Bezek's Split Flap Display — image 1
1 / 6

608 Bearing and/or Vase Mode Spool for Scott Bezek's Split Flap Display

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Spool and left plate edited to accept a 608 bearing, spool edited for vase mode printing to avoiding catching

Rating
0 / 5
Likes
3
Downloads
44
Makes
0
Views
228
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

--- THIS IS STILL VERY MUCH IN BETA!! ---

Denver3D's design is great for a 3D printed display, but I kept having reliability issues with the seams on the inside of the spools causing the motors to bind and lose steps.

Spool hub should be printed with normal settings, and uses the same style of alignment peg that the original used for the top cap. There's also an affirmative alignment stop, which the original lacked - I kept getting CA glue on my table while trying to get the original spool cap parallel to the top of the spool assembly.

The main spool is designed to be printed in vase mode. Play around with the outer wall thickness - I had the best luck with a .75mm outer wall layer and a .4mm nozzle, but it is a bit hard to push the spool into the groove on the hub uniformly. You'll need to manually set the number of bottom layers to 15 (assuming a .2mm layer height) to ensure the outer ring that the flaps set into are actually printed as part of the spool. 

Once you have both halves of the spool assembly, coat the outside of the hub's outer ring with CA glue or something similar and press the two halves together, ensure it's fully pressed together and properly aligned. You might be able to get away without gluing as long as the fit is tight enough, but I would be worried about the halves pulling apart as it operates or during assembly.

Printing like this avoids needing to sand or post process the inside of the spool after printing to avoid catching on the little nub above the motor, which the original design had trouble with.

Also included in this remix is a cut down rear mount (used originally for the driver and T-Display buddy) that just acts as a cross span - with a lot of modules I had issues with the back of the module deflecting under load, but you probably don't need it unless you're building a big display.

SUPPORTS ARE STILL REQUIRED FOR THE SPOOL BASE!

For bearings:

Using a 608 bearing is very overkill - you absolutely don't need to, I just had a lot of them around. If you do, I had the best luck cleaning out the factory grease on the shielded bearings I have by soaking them in isopropyl alcohol, since it sometimes add too much drag to the assembly for the motor to handle, and this is a very low speed application, so deviation and wear aren't really a concern. The bearings should be a loose press fit.

The modified left plate has a wider shaft to interface properly with the bearing, as well as a lip to press against the inner race of the bearing. It is otherwise identical.

All files other than the Left Plate and the modified Spools are the same as the original design.

The spool is pressed in correctly when the sides of the spool are parallel and the little alignment nub is fully below the lip of the hub - it should not sit proud. Try inserting the side with the nub fully first and then squeezing in the edge without letting go if you're having trouble getting it all the way inserted.

 

Without Bearings:

Just print and assemble the remixed spool files - you can use the original files for everything else! The vase mode files should still help with reliability and ease of assembly since you won't need to sand anything to avoid the display catching.

The spool is pressed in correctly when the sides of the spool are parallel and the little alignment nub is fully below the lip of the hub - it should not sit proud. Try inserting the side with the nub fully first and then squeezing in the edge without letting go if you're having trouble getting it all the way inserted.

Again, this is still very much an early design! I can't guarantee anything, but this is designed with the idea of improving reliability and ease of assembly, which is all the better for larger displays - I'm currently working on a 72-character display. 

1/20/25:
The left plate is replaced with V2 which has a better fit with the bearings. The old version sometimes was too tight and made the spool bind up.

Tags