XIAO Sense Case "Castle Bravo" (Seeed Studio ESP32S3 and Cam)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
An edited version of Fat Man, which extends out the LED winglets and gives them some ribbing for added strength.
- Rating
- 5 / 5
- Likes
- 24
- Downloads
- 528
- Makes
- 1
- Views
- 2,307
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Virtual Reality
- License
- Creative Commons — Attribution — Noncommercial
Should print fairly similar to the original design, I found my best results though at 0.16 layer height and printing the parts at an angle of XYZ 90, 45, 45. I think 0.2 layer height would work fine as well.
Using the auto-orient feature in Bambu Studio should achieve the desired result as well.
Use auto generated tree supports and randomize seam positions to increase the fitment of the shells.
UPDATE: I have added 2 new files, which add extra support material to prevent the winglets from cracking when press-fitting the LEDs into the case. Use the new files!
IF you have any questions please reach out to me in the Babble discord!!!
------------------------------ For da newbies------------------------------------
Q. Do I need a certain headset, or can I use any?
A. That's the awesome part about this, you can use ANY headset.
Q. How are the LEDS wired to the esp?
A. The extra space behind the board is for the wire I've used to solder from 5v (USB supply) to the LEDs, so I'm using a small wire from 5v through the thru-hole to the LED. From there, wire from the LED through both thru holes to other LED, and then wire from the LED through the thru-hole. In this case, the resistor which is then wired to the ground
The extra space in the back let me have somewhere to hide the extra wire lengths required when running wire through the case without needing to be too specific with wire lengths, and once I had the LEDs wired up I used a little electrical tape to cover up the bare conductors and exposed solder joints on the LEDs
Q. What size are the LED's?
A. LEDs have a forward voltage of 1.4v so I'm using the 5v rail and using two 220Ω resistors in parallel to make 110. 5mm 1.4 Foward drive voltage. link here: https://www.amazon.com/Infrared-Lighting-Electronics-Components-Emitting/dp/B01BVGIZIU?th=1
Q. What resistors to use, you said to use two in Parallel.
A. Through hole can work, the link is here: https://www.mouser.com/ProductDetail/TE-Connectivity-Neohm/EP2WSS220RJ?qs=HoCaDK9Nz5dMjnmRSmkRXg%3D%3D
Q. Parallel? What?
A. An explanation of how to wire in parallel can be found here: https://racheldebarros.com/wp-content/uploads/2023/05/leds-parallel-resistor-anode.jpg
Q. What ESP and camera are used?
A. Seeed Studio ESP32S3 Sense for the Board,Link: https://www.seeedstudio.com/XIAO-ESP32S3-Sense-p-5639.html?srsltid=AfmBOopuAW4OiJ54LKhhDob383i_vagXsRj2wtvkaQYbaqoyKtxmaLyC
and a 160-degree OV2640 NV 850nm camera. Link Here: https://www.aliexpress.com/i/3256801088377832.html?gatewayAdapt=4itemAdapt
Q. is this wireless? do I have to use a wire?
A. for this model it is suggested to use a wire as the higher the fps, the better. The good thing is that most headsets have a built-in hub! Just plug it in with your desired tip and you're good to go! Usb-c to Usb-c or Usb whatever wire. the shorter the better! This model and software give better results than the HTC Vive Face Tracker camera
Q. What software do I use?
A. https://github.com/Project-Babble/ProjectBabble/releases/tag/v2.0.5
Q. I have XXX Headset, where do I go for the mounts so I can mount the camera?
A. https://github.com/Project-Babble/BabbleHardware/tree/main
Q. SO THIS PROJECT IS AWESOME! What is the discord and how do I support this?
A. to support: https://www.patreon.com/user/membership?u=75292817
Discord is: in the membership link.