1 / 8
Morton MC30 Water Softener Valve Motor 7286039 Gear Replacement — image 1
1 / 8

Morton MC30 Water Softener Valve Motor 7286039 Gear Replacement

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Replacement gear for the valve motor assembly on a Morton MC30 water softener

Rating
0 / 5
Likes
6
Downloads
30
Makes
0
Views
163
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

PLEASE READ ALL OF THIS BEFORE ATTEMPTING A REPAIR

When my Morton MC30 reported Error 01, a valve malfunction, I took apart the valve assembly to find a gear with all of it's external teeth sheared and shattered off. Turned out the the valve had become stiff with age, and would barely move, even when I attempted to move it manually.

The valve likely became coated in iron deposits, leading to increased friction and drag, leading to the motor gear failure. To resolve this, you should to the following...

VALVE ASSEMBLY RECONDITIONING

  • Start printing your replacement gear while you work on this (printing tips in a section below)
  • ENGAGE THE WHOLE-HOUSE SOFTENER BYPASS VALVE so you don't get a face full of water when doing the next step
  • Disassemble the rotary valve assembly
    • Take note of all of the parts placement. TAKE PICTURES!
  • Using a straw, suck up any remaining water in the valve body
  • Lightly coat all the moving valve components in a food-safe grease
    • I recommend "Petrol-Gel Lubricant", found on Amazon for ~$7. Comes in handy for coating rubber seals on plumbing.
  • Re-assemble valve
  • Using the indexed gear, manually rotate the valve several times to ensure a good distribution of the lubricant internally and verify that it is moving more easily
  • Ensure that you have re-placed the valve cam switch next to the cam gear
  • Re-place the motor mounting cap
  • When re-placing the valve motor mount cap, if you intend to put the screws back in, be aware that the screws will bottom out WELL BEFORE THE HEAD DOES! This is because the screws are long enough to hold the geared motor in place. Don't over-drive them or you will damage the valve body cap!

GEAR BOX REPAIR

  • Using a knife (be careful) or a spudger tool, find the gap between the main gear case, and the flat cap.
  • Using the knife/spudger as a wedge, twist the tool to break the glue around the mounting holes one-by-one.
  • Remove the smaller gear holding the broken gear in place (white gear shown in provided pictures)
  • Remove the broken gear
  • Dry-fit your gear to verify fit
  • Replace the smaller gear above it
  • Re-place the flat cap, again verifying fit
  • Temporarily hold the gearbox edges together with some tape
  • Un-plug your water softener's power adapter
  • Re-plug in your motor gearbox
  • Plug in the water softener power
  • Verify that the motor moves without significant strain
  • Un-plug the water softener power
  • Un-plug the motor gearbox
  • Disassemble the gearbox again to access your 3D printed gear
  • Using the Petrol-Gel you used with the valve, coat the top and bottom mating surfaces of the gear shafts, as well as the gear teeth
  • Re-assemble the gearbox
  • At this point, you have some options on securing the case closed. I used a few #10 machine screws and nuts in the non-mounting holes to hold the case shut (see pictures). You could also use a small amount of cyanoacrylate (super/krazy) glue on the corners, but go easy in case you ever need to re-open it. And lastly you could again go with tape, at least temporarily as that would likely degrade with time.
  • Re-mount the gearbox to the valve motor mounting cap
  • Plug in your water softener
  • You should hear the motor engage, and occasionally hear the clicks of the cam switch clicking into place as the valve gear rotates
  • Re-open the whole-house bypass valve
  • Your water softener should proceed through a valve cycle or two before either starting a softener recharge, or going back to a waiting state. All errors should be clear at this point. You may optionally test your softener with a manual recharge cycle.

PRINTING TIPS

I printed this with the following material and settings (Cura 5.9.0):

  • Elegoo Rapid PETG (Nylon would probably also be a great option)
  • 0.4mm nozzle
  • 8 walls/perimeters
  • 6 top/bottom layers
  • 20% infill
  • Supports on
    • Used w/66% support interface density (not required, but can make for a smoother underside on supported gear surface)

I hope this helped you. When I saw the cost of a replacement motor gearbox assembly (~$60), I was irritated that Morton didn't design this to be more reliable, especially in regards to actually lubricating the valve itself. This was a fun project, which only took about an hour to design up, and a couple hours to print on my trusty CR10S. My hope is that this saves you some time and frustration as well, and gets you back in business in short order.

How I Designed This

Designed with OpenSCAD and the assistance of https://www.stlgears.com/generators/3dprint

Category: Replacement Parts

Tags