1 / 25
Hercules 20v Battery to Milwaukee M18 Tool Adapter — image 1
1 / 25

Hercules 20v Battery to Milwaukee M18 Tool Adapter

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Adapter to use Hercules 20 volt batteries on Milwaukee M18 power tools.

Rating
0 / 5
Likes
17
Downloads
149
Makes
0
Views
1,296
Reviews
0

Updated at source:

Model information

Category
Tools
License
Creative Commons — Public Domain

Overview

THIS HAS NO BATTERY PROTECTION - USE AT YOUR OWN RISK. There are 2 resistors installed to override the tool's built in battery protection and allow it to function. The latches to connect to the Milwaukee tool could use some refinement - they tend to stick. This doesn't bother me because I leave the adapter on the tool all the time.

Printing

This print requires supports. I used PETG with PLA supports (printed on Prusa XL). Make sure you do not have any supports in the terminal pockets, they will be impossible to remove. The provided 3mf files have painted on supports.

Additional Components

The following additional components will be needed for assembly:

  • (2 pieces) 14 gage wire, approximately 3-½" long (1 black, 1 red)
  • (2 pieces) Spade terminals for #6 screws (can substitute eyes, but it will make assembly more difficult)
  • (2 pieces) Stud mounted quick-disconnect terminals for #6 screws, ¼" tab width (McMaster-Carr #8015K53)
  • (2 pieces) 10k ohm resistor (Color code Brown Black Orange)
  • (2 pieces) Heat shrink tubing for resistors
  • (4 pieces) Terminals (https://www.ebay.com/itm/385486676382)
  • (6 pieces) #6-32 x ¼" long heat set inserts
  • (4 pieces) #6-32 x 3/8" long flat head (countersink) screws
  • (2 pieces) #6-32 x ¼" long pan head screws
  • 5/16 (8mm) diameter spring, approximately 1-¼" long

Assembly

Test fit to the tool and battery before assembly. The terminals in the tool side adapter are not removeable, so make sure to follow the instructions correctly. The images show the assembly steps outlined below.

  • Install the first latch tab, making sure it moves into the outward position. Install the spring through the hole. Use a ruler or narrow tool to push on the spring and install the second latch. Confirm both latches move as required, and test installing and removing from the tool.
  • Crimp a connector on the end of each wire with a resistor. The crimp should hold both the wire and resistor firmly. Install heat shrink over both resistors. Trim or fold excess resistor wire, and install a terminal on the other end of the resistor.
  • Install the wires in outermost slots in tool adapters, red under the plus side and black under the minus side (see photo). The terminals should latch in place.
  • Install the resistor terminals on the second slot in on the opposite side from the wire - the resistor connected to the black wire goes next to the red terminal and vice versa. See photo. The center slot is empty. Make sure there are no wires touching.
  • Bend the wires around into the cutout. They need to be back from the sides of the latches or you won't be able to remove the adapter from the tool.
  • Trim the wires to about ½" longer than the adapter. Trim excess insulation from the spade terminals, and install on the ends of the wires as in the photo.
  • Test fit on the tool. It may be difficult to install until the terminals wear in.
  • Use a long screw to start the heat set inserts in the inner holes on the battery adapter. Install inserts in these holes and also the top 4 holes. Do not use longer inserts or set them too deep - there needs to be a gap between the inserts or it will short out.
  • Install the stud mounted terminals in the slots with the hole over the inserts. Install the pan head screws, leaving loose for the spade terminals. Don't use longer screws here as it will short out.
  • Connect the wires from the tool adapter to the screws. The connector should fit in the pocket as shown. The wired do not cross; confirm that the red wire is connected to the side with the plus, and black on the side with the minus.
  • Assemble the 2 pieces, taking care not to pinch the wires. Use the flat head screws to hold it together.
  • Test the adapter. If the tool runs for only a few seconds and cuts out, this is the battery protection. Check that you have the resistors installed correctly.

Remixing

I have provided step and FreeCAD source files for anyone who wishes to remix. I only ask that you have the same courtesy and upload step files for your remixes.

Please note that many of the dimensions in the FreeCAD model are linked to other sketches and profiles, so watch what you edit.

 

 

Tags