Qidi Plus 4 Auxiliary Fan HEPA Charcoal filter
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Activated carbon and HEPA filter system which clips over the Qidi Plus 4 auxiliary cooling fan.
- Rating
- 5 / 5
- Likes
- 39
- Downloads
- 106
- Makes
- 1
- Views
- 1,237
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- GNU General Public License v3.0
Note, see the remix of this model by Mike Wil for 15mm thick filters rather than 14mm filters, and with even more clearance from the z-blocks than the V3 version if required.
V3 - A user reported that the V2 clashed slightly with the Z rod blocks so revised to add slightly more clearance from these blocks. I'd suggest printing these in case you need the space.
V2 - A user reported that there was insufficient space for the camera cable with the first version so V2 versions of the left and right boxes have been added with more space for the cable. I haven't printed these to test but other than a very slight reduction in air-flow there should be no disadvantage so I'd suggest printing the V2 versions in case you need the space.
A recirculating activated carbon and HEPA filter system which clips over the Qidi Plus 4 auxiliary cooling fan.
Designed using magnets to assemble so that it can be removed quickly if fan is needed for printing PLA.
Print in ASA or other heat resistant filament.
Print in the orientation shown in the screenshot without supports.
BOM:
28 No. 6mm dia x3mm deep magnets.
Superglue to glue magnets in holes.
3 No. HEPA filters for iLife V3 robot vaccum, I used:
https://www.amazon.co.uk/gp/product/B07BMDWD3C.
Activated carbon pellets of any size, or Nevermore Scorch, or a 50/50 mix depending on chamber temperature used.
ASSEMBLY:
Print the 4 parts.
Make sure magnets are in matched attracting pairs before installing at each location.
Put a spot of superglue in each hole and install the magnet.
The holes should not be too tight, this is to allow the magnet to be installed flush or slightly below the surround. Make sure not to leave the magnets projecting, and wipe any glue excess away before it sets.
Slide the 3 HEPA filters into the vertical box. Make sure the bottom filter goes down into the recess in the base and that the filters are pushed tight against each other. They should be a fairly tight fit with no gaps.
Note that the space remaining for the camera cable along the top of the filter system is tight, be careful not to damage it when installing the filter. You may wish to add some tape to secure the cable better, particularly if you plan on installing and removing the filter frequently. There is also a P-clip securing the cable at the front of the printer that will require unscrewing and replacing with tape as it clashes with the right block.
Install the bottom support block in the orientation shown in the screenshot and photo, noting the channel in the base to avoid the bolt head protuding from the printer base.
Install the left block over the auxiliary fan, may need to wiggle the fan slightly depending on position. Slide forward using the handle on the bottom until engaged.
Install the right block over the auxiliary fan, making sure lip and magnets properly connected.
Fill filter box with charcoal / scorch close to the top, shake it a few times to make sure it is settled and completely filled.
Slide the filter box between the support block and the right block. You'll need to tip it slightly but don't spill the carbon. Adjust all the parts so that they are well aligned and the magnets are connected.
I have tested it up to 75% fan speed and this gives a good flow through the filters. Lower speeds made my fan rattle badly. This is not due to the installed filter, it rattles without the filter.
Fan can be turned on in Fluidd, set to come on during prints in slicer of choice, or added to the Print Start and Print End macros.