Zeolite & HEPA fume-hood-like-filter for Qidi Max3
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Fume-hood like air filter designed for Qidi Max3 that use Zeolite filter to remove Vocs produced during printing process
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 11
- Makes
- 0
- Views
- 273
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Introduction:
Concerned about the Vocs produced by printer, I believe a fume-hood like air filter would be helpful to remove most of the odeur gaz from the inside of the printer before they diffuse into the surrounding.
This design has already been verified (by me) in real world.
For a quick intro to Zeolite Filter. Plz consult (Industries using honeycomb zeolite filters for VOC removal (2024) SKY environmental technologies. Available at: https://skyemission.com/what-industries-commonly-use-honeycomb-zeolite-filters-for-voc-removal/ )
Specification:
This filter contains four 12V 3.96A 12032 FAN (DELTA BFB1212GH-A) 60.4 CFM each. The CFM number has been calculated based on the open surface area when the door is opened (100fpm/square foot). Hence, the CFM needed should be superior than 225 CFM.
Filter is composed by [5mm Activated Carbon Tissu, 100*100*100mm Zeolite Filter, 100*100*20mm (W, L, H) HEPA Filter] in order from where air enters to where air exits.
Material:
Enough 3D filament, electrical filament
65 * M5 * 5mm Long Heat-Set Inserts (100 is better)
8 * M5 * 10 mm Long Heat-Set Inserts (30 is better)
12 * M4 * 5 mm Long Heat-Set Inserts (20 is better)
12 * M3 * 5 mm Long Heat-Set Inserts (20 is better)
4 * 12V 60 CFM FAN
8* M5 * 160 mm Long Screws
50 * M5 * 14 mm Long Screws
50 * M5 * 10 mm Long Screws
50 * M4 * 6 mm Long Screws
1 * 250W 12V Power Supply (I installed a mini power supply in the Qidi Max3 Control Box (110V to 12V). Don't use 24V power supply in the printer as it may overload)
2 meter 5mm width sponge sticker
[optional] 1 * microcontroller (Control the fan speed when the door is opened)
[optional] 1 * DC PWM Voltage controller (Connected to the MCU)
[optional] 1 * Magnetic switch (Detect the state of the front door)
[optional] Some Strong Glue to fix the FAN COVER
Build:
Print ALL FILES according to their filename (Ignore OPTIONAL FAN COVER IF NO NEED)
Insert inserts in corresponding places. (According to the depth of the hole and diameter)
Assemble all parts
[optional] If want to control the fan speed with respective to the door's position, need to fix a magnetic switch and connect it to the MCU. In addition, more electrical wiring is needed to make the voltage controller works.
Filter Structure:
AIR ENTRANCE → FILTER-DOWNSIDE → 5mm Activated Carbon Filter → FILTER-INNERISOLATOR → Zeolite Cube → HEPA Filter → Filter-UPSIDE → AIR OUTLET
Points to notice:
Builders want to use sponge stickers around the hole where air exits from the FANBOX in order to scelle the structure (a little bit).
Builders want to fix the CENTRAL PLATE of the FANBOX after having tightened the screws that connect the FANBOX with the CORNERS and CONNECTORS.
The only M5 * 10 screws are used in the CENTRAL PLATE.
Use M4 * 5 inserts for the FAN holes.
Printer 4 times the FANBOX-INNERISOLATOR
This design is solid, no renforcement needed but takes some filament to print. (PA66 CF USED)
Where to buy filters:
[optional]: https://www.alibaba.com/product-detail/Impregnated-KOH-Iodine-800mg-g-Activated_1600770464318.html
Activated Carbon: https://www.amazon.ca/Compost-Filters-Activated-Kitchen-Countertop/dp/B09F6793ST
HEPA: https://www.alibaba.com/product-detail/Customized-H13-True-HEPA-Filter-Pre_1601043615727.html
(I Recommend to use Zeolite filter with 3mm holes)
(ASK HEPA vendor for accurate dimensions. Should be 100mm 100mm 20 mm W*L*H)
User experience (my own):
Well, this thing works as I intended. It may take some time to build, but it works. I have tested its suction speed with an incense, no noticeable aromatic odeur diffuses in air when the burning incense is placed in the printer with door opened.
Update: I have changed filament (PA66-CF) with door opened. This filter has taken out the smell successfully. It produces a very loud sound I shall say, but the smell just disappears.
No smoke is getting out from the door.
