1 / 14
Legacy 1/3 Scale Federal Signal 3T22A (True Collab Model) — image 1
1 / 14

Legacy 1/3 Scale Federal Signal 3T22A (True Collab Model)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Small scale version of the real 3T22 that federal made back in the day

Rating
0 / 5
Likes
10
Downloads
52
Makes
0
Views
544
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

This is a 1/3 Scale 3T22A (or 2T22A) with WORKING DAMPERS!!! This siren was a collaboration between Nascarsimracing1 and I

This siren weighs approximately 9 pounds!

Thank you Jared for modeling this, my old modified Edaan B-core may be dead, but now I can run/hear HI-LO again!

 

READ ME:

Supports:
The only parts that need to be printed with supports are the stators
Overhang Angle: 80 degrees
Support Type: Tree

Cooling:

Fan Speed: 20 percent/initial fan speed 0 percent (May need to change for your printer.  Keep fan low to prevent warp)

Infill:

Rotors: 99/100% infill (Lines)
All other parts: 20% infill (Gyroid)

Material:

Motor Covers and Solenoid Boxes: PETG/PETG+
Everything else: PLA/PLA+

(I recommend ESUN PLA+ and ESUN PETG.  But any brand PETG/PETG+ and PLA/PLA+ should work just fine.)

Colors:

Rotors, damper shaft, damper arm, and damper rod: Grey (I used Esun PLA+ Silver)
Everything else: Yellow (I used Hatchbox PETG Yellow and Esun PLA+ Yellow) - Nascars' old build

Rotors and stand I printed in Gray Esun PLA+ (I painted my stand blue), horns in white PLA+, and everything else I printed in PETG/PETG+ then painted blue - My 3T22 build

Motor: Samsung microwave blower: DE31-00029H, DE31-00029K, DE31-00029G, and DE31-00029J are all compatible motor variants, it does not matter if the motor is flat face or ribbed

These are all over Ebay and can sometimes be found as low as 20$. I recommend the DE31-00029H/K/G because they are more common. (As of January 2026 this is still mostly true)

For the DE31-00029H and DE31-00029K, we recommend using two 5uf capacitors in parallel for a total of 10uf.  For the DE31-00029J, we recommend two 4uf for 8uf total. (Use the 4uf listing for easier sourcing)

The capacitor to buy, it perfectly fits in the current junction box!
https://www.amazon.com/dp/B0143VJN40?ref=ppx_yo2ov_dt_b_fed_asin_title

https://ebay.us/m/GCSfs9
LS90120 (4mm Thick) weight (This glues to the back of the 10 port)

If you want to have the less common Northwestern motor instead of the Marathon, you can download Jared's Northwestern model from his page here: https://www.printables.com/model/856717-13-scale-federal-signal-3t22a-redone

 

Hardware:

M4x14mm (or 16mm) machine screws (6x)  Stand + spacers to the intake

M4x6mm machine screws (7x) Stand and A frame

M4 nuts (13x)

M3x12mm machine screws (55x) Intakes and horns

M3x10mm machine screws (24x) Solenoids, solenoid boxes to intake, and damper rod. And then 3 on each motor cover to hold the stator to the motor.   Also 3 on each valve to hold them to the shaft.

M3 washers (6x) used for the M3x10mm screws holding the stators to the motor covers

M3x8mm machine screws (8x) Solenoid box covers

M3x6mm machine screws (4x) Hold junction box to the motor

M3 nuts (65x)

M2x10mm machine screws (2x) Hold damper arm to damper shaft.

M2x8mm machine screws (24x) Valve stops and hinge covers

M2x4mm machine screws (4x) Junction box cover (You can also use longer M2s)

M2 nuts (26x)

1/4" x 2-1/2" eyebolt (I walked into my local Lowes and bought the black one they have, comes with a nut too)

A couple 1/4" washers (for the eyebolt)

M3x5.7mm brass threaded inserts (14x)
https://www.amazon.com/gp/product/B081BCRZZS3   (I used these)

Cable clamp connector 1/2" knockout and 3/8" trade size

Solenoids:
JF-0826 (I used 12V but Jared used 24V ones and they also work the same)

https://www.amazon.com/dp/B0C9QW42NM?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1
Shaft Collars

https://www.amazon.com/dp/B0BF8S7231?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1
Shaft Couplers

https://www.amazon.com/dp/B0D2Q2QW43?ref=ppx_yo2ov_dt_b_fed_asin_title
Slotted Weights

Rotor installation: (Legacy Pressfit)

Print the 8mm tolerance tool in the same settings you will print the rotors. Then take it and press it on your motor.  

Whichever numbered hole fits snug but not too tight for you, select the corresponding rotors with that hole number.

Hole 1 is 8mm, and the following holes go up by 0.1mm increments.

Take the shaft collar and put one on each side of the motor shaft, eyeball it to be just a little below the stator ports, then press the correct hole rotor on the shaft, if the rotor isn't low enough, remove it then loosen the collar set screw and move it back a little more. If the rotor isn't a tight enough fit, you can use some tape placed on the shaft to increase the tightness of the pressfit

I will eventually release rotors that use shaft couplers instead so that installation and removal is more simple

Rotor installation: (Shaft Coupler Variant Available Now!)

After printing just the rotors (You don't need the tolerance tool), put two set screws into one end of the shaft coupler, there are two holes parallel to each other, make sure the set screws are screwed in far enough that they aren't sticking out.

Using the holes in the rotor for reference, align the shaft coupler's set screw hole with the hole in the rotor. 

Then place the rotor face down and force the coupler in. If needed use a hammer and tap lightly.

Once you've done these steps, take a long 2mm hex driver or long end of an allen wrench/key, loosen the screw just enough that you can simply slide the rotor on the motor shaft, then tighten (Be careful to not strip it!)

"Once you have assembled the siren, you should secure the siren with tape or bolt it to a mount (M4 machine screws)." -- Nascars' recommendation, really for certain sirens, the Mini XT22 is fine without a mount, but if you're doing roof mount style, do not print the full length legs!

"If u don't do this, the siren will spin on startup like that Screamer did at SirenCon 2022." -- Nascars' common printables quote for his siren releases

The model and page is subject to change

Tags