Magnetic Focuser for the Takahashi TSA-120
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Do you own a Takahashi TSA-120? And a Gemini Focuser? And you want a fast attach/detach solution? Then this is for you!
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 9
- Makes
- 0
- Views
- 78
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Physics & Astronomy
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Added an O-Ring to the coupler (scope side)
To reduce the sliding of the coupler on the focuser axle, due to the low friction between the plastic and the steel, I modified the design adding a 10 mm OD x 2.4 mm O-Ring. The O-Ring is compressed by the conical point of the focuser's axle.
The modification is optional.
Extra component:
#1 O-Ring, EPDM or similar elastomer, 10x2.4 mm (optional)
_____________________________________________________________________________________
Rev. 2:
For the geeks and really passioned people:
- Added an (optional) ball bearing :-) to keep the focuser axle well centered
- Adapted the Clamp Lo and couplers to fit the ball bearing
- Minor improvements
If you go with the (optional) ball bearing all you need is to print the sleeve which goes onto the Tak focuser shaft to fit the ball bearing hole.
Extra component:
- #1 Ball Bearing, 10x26x8 (optional)
_______________________________________________________________________________________
I reworked the excellent MagneTIC focuser by Luke (@Luke_3D) for my Tak TSA-120. Unfortunately, I couldn't get the Pololu TIC T500 to work under Windows, as the Ascom driver found on GitHub appears to be broken. However, the MagneTIC's elegant design, particularly its ability to easily attach/detach the motor for manual focusing, was something I wanted to retain.
Therefore, I decided to adapt the MagneTIC concept to the Gemini focuser, an inexpensive automatic focuser available on eBay for 70-80 euros. Due to the absence of threaded holes on the bottom of the TSA-120 draw tube, a clamped connector was the only viable solution. This necessitated an extensive rework of the MagneTIC, requiring the remodeling of all its components.
After the usual fine adjustments and a fair amount of wasted filament, the assembly was successfully tested.
If you download/enjoy it, please leave a like!
Advantages
Compared to a traditional setup using an L-bracket, this modification offers the following advantages:
- Eliminates the need for a coupler with grub screws on the focuser shaft, preventing potential marks and scratches.
- Allows for quick attachment and detachment of the motor, enabling a swift return to manual focusing.
Components
The following components were used in this modification:
- A Takahashi TSA-120 :-)
- The Gemini Automatic Star Focuser Pro
- 8 x #8 neodymium magnets 9x5 mm (available on AliExpress)
- 1 x M5x30+ bolt and nut with a hex cylinder head (for tightening the clamp)
- 2 x M4x20 bolts (to attach the magnetic plate to the Gemini focuser)
- 1mm adhesive felt, 15mm wide (or any other 1mm ribbon for the inner clamp). I used this one from AliExpress which provides excellent grip.
- 2 x M4x4 or M4x6 hex grub screws with a flat head (DIN 915) for the stepper-side coupler. Avoid cup-head screws as they may heavily mark the shaft.
- 2 x M3x8 or M3x10 self-tapping screws (optional, for securing the cable organizer to the clamp).
- Superglue (for securing the magnets).
Instructions
Clamp
- The two halves are designed to join with a snap-fit hinge. It should print successfully upright without the need for supports.
- The lower half, which includes the focuser adapter, printed successfully without supports on my Prusa Mini. If you encounter issues, I recommend using organic supports.
- The clamp is secured using an M5x30 bolt and nut with a hex cylindrical head. Secure the four magnets within their designated slots using superglue or a similar adhesive.
Magnetic Plate
Attach the four magnets inside their slots using superglue or a similar adhesive.
Couplers
- I implemented a 'progressive fit' for the two coupler halves to minimize stiction and eliminate any play.
- Both couplers should print successfully without the need for supports.
- The coupler on the Gemini side is attached to the shaft using two M4 grub screws.
- The coupler on the telescope side is secured using the M4 Phillips screw from the TSA-120's original aluminum wheel, or any other M4 button head screw.
Cable Organizer
Optional. It can be attached to the upper half of the clamp using two M3x8 self-tapping screws.
Notes
- I only remodeled the pieces due to the extensive modifications required to fit the Takahashi TSA-120 focuser. Luke's original design is truly excellent.
- It is recommended to print the snap-fit pin and cable holder in PETG for optimal results, although PLA is also a viable option.
- Both PETG and PLA are suitable materials for the clamps and magnetic plate; however, I prefer PLA.
- Due to the remodeling process and the unavailability of Luke's STEP files, the new couplers are likely incompatible with his original design (featuring 22 teeth compared to 20, and different depths). I believe this modification is permitted under the 'remix' license.
Useful Data
- steps/turn=3840 (Gemini)
- Draw Tube Travel: 86 mm (stock Takahashi focuser)
- travel/step: 6.3 micron
- travel/turn: 24.3 mm
- CFZ: 150 micron
- NCFZ: 60 micron (1.2" seeing, 10% tolerance)