1 / 2
LED Mount Nubs (and spacer jig) to retrofit the earlier minimal enclosure riser — image 1
1 / 2

LED Mount Nubs (and spacer jig) to retrofit the earlier minimal enclosure riser

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a set of nubs and spacer jig, for adding FF LED light bar to earlier Minimal Enclosure, before the new v3.0 set!

Rating
0 / 5
Likes
18
Downloads
66
Makes
0
Views
886
Reviews
0

Updated at source:

Model information

Category
Accessories
License
Creative Commons — Attribution — Noncommercial — Share Alike

This pertains to the "Flashforge Adventurer 5M (AD5M) Minimal DIY Enclosure - prints faster, uses less plastic - and more" — https://www.printables.com/model/1130485-flashforge-adventurer-5m-ad5m-minimal-diy-enclosur 

This is a set of nubs and spacer jig, for adding FF LED light bar to the riser set of the earlier Minimal Enclosure, before the new v3.0 set added the nubs back into the download set.

The nubs can be attached with either glue or screws or both. Of the 3 screw holes, the top and bottom are more for attachment of the nub, while the middle screw hole is for attachment of the light bar. The holes are designed as 2.5 mm in diameter. If you design to use screws, you probably would want to pre-drill using a smaller bit, and the screws should probably be the “self tapping” type that are typically used for plastic. If it were me, I'd CA glue them in place and call it done.  

The spacer jig is meant to be temporary. Use painters tape to put the jig in the center as shown, and then the jig guides for placement of the nubs, as shown.

Please note: You can use these to retrofit the front two parts of the top riser set, so they have nubs like the OG enclosure. However, consider what I think is a better approach: putting LED strips inside the steel metal frame. That's what I did. If you attach the Flashforge LED light bar to the printed riser set, then if you ever need to remove the riser set to work on something, then you will still have a wire for the LEDs that is tethering your riser set, and you'd probably want to add into wiring some type of quick disconnect. Whereas, if the LED lights are positioned on the inside of the metal frame, then your LEDs and your wiring don't have to be disturbed — just lift the riser set away and replace it when done. Here's a link to two key listings I offered with regard to how I did my LED lights: https://www.printables.com/@design8studio/models?search=ad5m%29+led

Also note: the new v3.0 riser set for the Minimal Enclosure, now includes nubs built into the print files. Here's a link to the new set: https://www.printables.com/model/1247920-new-v30-of-top-riser-set-for-flashforge-adventurer 

 

Related info:

In addition to the video and installation guide linked below, for the remixed side mounted spool holder, be sure to check out the BOM and installation tips on that listing here:

If you either watch the Flashforge video on how to assemble the DIY enclosure, or get from their Wiki the details on it, you will get a good handle on mine. Most everything will be the same or very similar. Both are below!

NOTE: The two side verticals in the back... I CA-glued the top to the bottom on each, before attaching them with screws. I will look into whether something can be done to make it better.

Flashforge video:

And here's the link to the Flashforge Wiki with the details on the DIY enclosure:

And from the wiki, here are links to the installation guide in a variety of languages:

Finally, you may want to check out my many other remixes for the AD5M (see partial list below), including my mount for the side cutters, and matching safety cap for the side cutters:

Flashforge Adventurer 5M (AD5M) Side Cutter Mount v1.0

Safety Cover for Side-Cutter Tips

 

Other cool options for the AD5M

 

You may also like my other AD5M related design work:

Use Klipper stuff on AD5M stock hardware…

Check out other cool AD5M related options here:

 

My PayPal tip jar: https://paypal.me/design8studio