Surgiscreen antigram holder for QuidelOrtho Vision analysers
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
An over-monitor frame for QuidelOrtho Vision analysers, to securely hold the antigram slips for Surgiscreen reagents.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 0
- Makes
- 0
- Views
- 8
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Gadgets
- License
- Creative Commons — Attribution
A frame allowing the paper antigram slip from Surgiscreen reagents to be conveniently displayed over the monitor of a QuidelOrtho Vision analyser. This is also compatible with the Vision Swift analyser.
In addition to the printed materials you will need up to 14 m3x10 socket screws and one sheet of clear acetate film (ideally overhead projector printable acetate).
Print the following platters in PETG (Note that the top and bottom frame parts are very long and thin; depending on your ambient temperature you may find that you need brim enabled to prevent warping, even with PETG):
Platter 1: Stand
Platter 2: Both halves of the back, and frame left and right with support enforcers for each end
Platter 3: Frame top
Then either (if using just the frame):
Platter 4: Frame bottom
Or (if also using the reagent rack covers from my other project Reagent rack covers for QuidelOrtho Vision analysers):
Platter 5: Frame bottom with holes for hooks, and
Platter 6: Hooks - NOTE: There is a layer change for the last two top layers, to allow a contrasting filament to be swapped in and show the lettering better.
To assemble the frame, you will need 10x m3x10 socket screws (no hooks) or 14x m3x10 socket screws (with hooks).
Place both halves of the back together. They are keyed to lock together loosely.
Place the stand on the back, so the arms point downwards, away from the central top notch in the back plate. Fix in place using 6x m3x10 screws as below.

Fit the top, bottom, left and right frame parts together so you can see how they will attach to the back plate, as below. The left and right parts have the protruding L section at the bottom.
Note at this point, that if you are wanting to use the hooks, they need attaching to the bottom rail first. attach each one to the bottom rail with 2x M3x10 screws, ensuring the hooks are the right way up (the rail with hooks appears in the below image, underneath the rail without hooks that it replaces).

Secure each corner of the frame through the back of the backplate.
Look at the back of the Ortho Vision monitor. The barcode scanner holder which is made from bent metal bar should have two ends sticking up out of the top of the metal bracket. The stand has two holes in the bottom rails that are a tight push fit onto those metal bars. If the barcode scanner holder has been fitted particularly low, you may need to loosen the bars slightly and move it up until there is enough bar above the metal bracket for it to secure onto. Make sure everything is retightened afterwards.

You will also need clear plastic sheet cut to match the sleeve template PDF (scaled for A4 paper). The easiest way to do this is to print directly to a clear overhead projector sheet, otherwise you will need to manually trace onto a piece of thin acetate sheet. Cut around the solid outer line, and fold sharply along the central dotted line. Clearance top to bottom is not particularly important, but clearance side to side is. You may find that for ease of inserting into the frame, you need to trim a tiny bit off the sides of the plastic sleeve.
To display the antigram sheet, load into the clear plastic sleeve and lower into the frame at the top. The tabs on the sleeve should stick up just far enough to be grabbed and removed using the notch at the top.
If the hooks are added, then the reagent rack covers from my other project can be placed on the hooks to indicate what reagents are currently loaded.