Storage bins for foam-backed sanding sticks (Gridfinity-compatible).
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Gridfinity storage tray-and-bin pair for 6 grits of sanding foam sticks (20pc each).
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 42
- Makes
- 0
- Views
- 402
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Tools
- License
- Creative Commons — Attribution — Share Alike
This pair of bins was made to store my foam-backed sanding sticks; the set (Amazon ES, Amazon US, not affiliate links) contains 20 sticks of 6 different grits, #80, #100, #120, #180, #240, and #320 (which I assume follow American / CAMI grit nomenclature).
The idea is to have a top bin with the currently-in-use (but still not worn out) sticks, while keeping the fresh ones away, in the bottom bin, as inventory. I can also move the tray around to where it's needed, it's just less bulk.
As these are stored in the upper drawers of an Ikea Alex (Wide) cabinet, and since the drawers have Gridfinity baseplates glued on them, I am limited to a maximum “Gridfinity height” of 8U. As such, I designed the top bin as a 4*3*2U bin, and the bottom bin as a 4*3*6U bin; both have 6 subdivisions, and I chose to keep the label tab, as the sticks themselves are not marked with their grit.
However, the sticks are 16cm long, and to make them fit in the labelled bins, I had to generate the bins without “finger slides”, and to cut 1cm off the sticks' ends; if you print the STLs without the label tabs, then you can fit the whole 16cm in it (they still do not have the “finger slides”).
Without overflowing the tacking lip, 19 sticks fit in the bottom bin, if just barely, (and 1 on the top tray), but if you forgo the top tray, you can easily heap the whole 20 in the 6U bin. I'm keeping on the tray a 2nd stick cut from 15cm to 5cm+10cm to sand in tight places, and 18 sticks fit comfortably in the bottom bin.
I designed these with Perplexing Lab's Extended Gridfinity Generator; parameters for each bin are almost identical ("tray / bin"), and are as follows:
- Grid rows 4
- Grid columns 3
- Height (7mm "u" units) 2 / 6
- Grid base size 42
- Stacking lip style normal
- Solid (no)
- Wall thickness 0,95
- Spacer mode (no)
- Single contiugous* base (no) (*typo is from the generator)
- Fancy sub-bin walls (no)
- Sub-bin columns 6
- Sub-bin rows 1
- Sub-bin wall thickness 1,2
- Bin floor-wall radius 3
- Attachments on corners only (yes)
- Magnet diameter 6,1 (for 6*2mm disc magnets)
- Screw hole depth 6
- Hole overhang remedy X+Y
- Center magnet diameter 0
- Center magnet thickness 0
- Floor thickness 1,2
- Efficient floor off
- Label tab style normal (or off)
- Label tab position left (or off)
- Label tab relief 0
- Label tab width 0
- Label tab depth 14
- Label tab height 14
- Label tab fillet radius 0,6
- Finger Slide none
- Tapered corner style none
- Enable wall patterns (no) (v1 had them, and the sticks fell through)
- Side wall cutout enabled (no) (no point, still can't reach inner sub-bins)
[Edited to add: printed with a 0,6mm nozzle at a 0,3mm layer height with a speeds range of 50mm/s to 150mm/s, no brim, 3 skirt loops, and supports (just a pip where the Gridfinity lines intersect at the bottom). Used 262,44g of filament, and took 5h2m.
Sliced on OrcaSlicer 2.3.0, printed on an Ender-3 V3 Plus, using Elegoo PLA Marble.
Leave any questions in the “Comments” section, and I'll address them as I can.