1 / 3
Carpodgo T3 Pro VW Polo 9n3 dash tray mount — image 1
1 / 3

Carpodgo T3 Pro VW Polo 9n3 dash tray mount

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Carpodgo T3 Pro VW Polo 9n3 dash tray mount, may work for other Carpodgo models.

Rating
0 / 5
Likes
2
Downloads
14
Makes
0
Views
822
Reviews
0

Updated at source:

Model information

Category
Automotive
License
Creative Commons — Attribution — Noncommercial — Share Alike

Apologies for the pictures, we sold the car before I had the chance to take proper photos.

We bought a Carpodgo T3 Pro (2024 model) for our old 9N3 Polo GTI to replace a troublesome Carpuride unit, has been a much better experience.

So I decided to make a more permanent dash tray mount for this Carpodgo unit, as I did originally with my old Carpuride unit (see that one here): https://www.printables.com/model/1023761-carpuride-w701-vw-polo-9n3-dash-tray-riser-mount


To fit the mount you will require:

*M3 16mm or 20mm mm bolts x 6 preferably countersunk (20mm to be safe, forget exact as sold the car a while ago)
*M3 nylock nuts x 6
*M3 washers x 6 (optional - should help prevent the nuts damaging bolt holes in plastic over time)
*4mm drill bit
*sharpie
*Nylon spudger/pry or similar
*(optional) Replacement 9n3 dash tray from Aliexpress if you do not wish to damage your original. They are AU$15 delivered for me, well worth not ruining your original OEM dash tray as they can be expensive second hand if you wish to reverse the mod at a later date)
*Filament better than PLA if you want it to last in the sun, I used PC/Polycarbonate.


Instructions:


1)Print the mount laying down so that you do not have to use any supports and the rectangle hole turns out clean. The screw holes will of course print without support too. As mentioned earlier, use something better than PLA, Polycarbonate seemed to be most recommended to me, and I figure it will be good under harsh UV.  Printed on a Bambu A1 using Generic Polycarbonate settings, 0.4mm nozzle and the Extra Draft 0.28 layer height. 

2)Print the end cap in polycarbonate, and print the drill template in PLA or whatever is cheap.

3)Pry up the dash tray with a nylon spudger from the top left or right (it's easy, use youtube guide if unsure), 

4)Use a sharpie to mark 6 holes in dash tray using the tabs on the drill template to roughly align them (note the orientation of the mount/screw holes on the dash tray in my photos). 

5)Drill the 6 mounting holes in the dash tray (now may also be the time to test fit the mount to figure out if you want a usb C charging cable hole and drill that if you wish to route the cable behind the dash/head unit)

6)Attach the mount using the m3 bolts/nuts and torque them down decently. Washers under the nuts are recommended to prevent the holes being damaged over time with vibration etc.

7)Partly disassemble the rectangular bar on the Carpodgo's suction mount. You will need the Carpodgo magnet + ball joint with the rectangular bar attached to it, the thumb screw piece, and the internal rectangular nut piece. The rest of the suction part of the mount is unneeded. 

8)Assemble the mount. Examine the photos if you are confused as to how it goes together. The hardest part is aligning the internal nut piece in there and screwing down the thumb screw.

9)Put your dash tray back in your dash with the mount, place the Carpodgo in the holder and adjust it to a a good angle so that the device sites on the edge of the dash tray, then use the sticky strips provided in the Carpodgo box to stick it down so it does not vibrate.

9)Finish off the rear end of the rectangular tube with the end cap.

Tags