Skateboard Rad / Skateboard wheel / Longboard wheel D70 x 43
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Longboard wheel D70 x 43 UPDATE 16.08.2024
- Rating
- 0 / 5
- Likes
- 29
- Downloads
- 212
- Makes
- 1
- Views
- 1,144
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Sports
- License
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Skateboard Rad / Skateboard wheel / Longboard wheel D70 x 43
!!! HAFTUNGSAUSSCHLUSS !!!
Ich habe sie nicht getestet. Für den Reifen empfehle TPU möglichst hart (100% Füllung).
Für die Felgen empfehle ich PETG (100% Füllung, vielleicht Carbon verstärkt ).
Beim Fügen / Einpressen Montagerichtung (Bild 2) beachten und eventuell den Reifen vorher in warmes Wasser tauchen!
Der Einsatz sollte eine ebene, glatte Fläche sein.
Sie sind nicht für Sprünge oder andere Stunts gedacht.
Achten Sie auf ausreichende Schutzausrüstung ( Protektoren, Helm…)
Herstellung und Verwendung auf eigene Gefahr!
Wie oben beschrieben noch nicht getestet.
UPDATE 16.08.2024
Joel Klavins hat hier einen Make hinterlassen, Danke.
Um Schwierigkeiten wie von Ihm beschrieben zu vermeiden habe ich hierfür nochmal eine Fügehilfe erstellt und Download bereitgestellt.
Vorgehen wie folgt:
Den Reifen (das Außen Teil) ziemlich lange (ich schätze, wenigstens eine Stunde, (wegen geringer Wärmeleitfähigkeit) bei ca.90°C gut durchwärmen. Etwas Seife ( Geschirr-spül) auf der Felge ist auch hilfreich. Beim einpressen ist zum einen eine große Kraft erforderlich und zum anderen ist gerades (axiales) pressen wichtig. (zum Beispiel mit einer Ständerbohrmaschine OHNE Rotation.) Ich habe mal einen Kern zum einpressen in der Bohrmaschine zum Download nachgereicht. In das Gewinde eine M6 Inbus-Schraube mit großer Unterlegscheibe ein-schrauben, den Kopf der Schraube im Bohrfutter aufnehmen und dann nach erwärmen des Reifens "AXIAL" einpressen.
----------------------------------------------------------
Google translates:
Skateboard wheel / Skateboard wheel / Longboard wheel D70 x 43
!!! DISCLAIMER !!!
I haven't tested them. For the tire recommend TPU as hard as possible (100% filling).
For the rims I recommend PETG (100% filling, maybe carbon reinforced).
When joining / pressing in, observe the assembly direction (image 2) and possibly immerse the tire in warm water beforehand!
The insert should be a flat, smooth surface.
They are not intended for jumping or other stunts.
Make sure you have sufficient protective equipment (protectors, helmet...)
Manufacture and use at your own risk!
As described above, not yet tested.
UPDATE 08/16/2024
Joel Klavins left a make here, thanks.
In order to avoid difficulties as described by him, I have created another joining aid and made it available for download.
Proceed as follows:
The tire (the outer part) for quite a long time (I guess at least an hour
, (due to low thermal conductivity) warm thoroughly at approx. 90°C. A little soap (dishwasher) on the rim is also helpful. When pressing in, a lot of force is required and straight (axial) pressing is important. (for example with a pillar drill WITHOUT rotation.
) I have submitted a core to be pressed into the drill for download. Screw an M6 Allen screw with a large washer into the thread, hold the head of the screw in the drill chuck and then press in "AXIAL" after the tire has heated up.