(Penta) Baby mobile and clamp (Chicco Next2Me)
We calculate the final price from your selected file. You review and accept it before payment.
Estimated printing price per file
€0.08 – €0.09 net (excluding VAT)
For file: ring_9mmweight_0.6n_0.3mm_PLA_MINI_5m.gcode
This is an estimate for one file. You’ll confirm the exact price before ordering.
File and estimate settings
File used for this estimate
Average indicative estimate: €0.09 excluding VAT (range midpoint).
- Weight reported by the author
- 1 g
- Print time reported by the author
- 5.4 min
- Source material
- PLA
- Estimate material
- PLA
- Estimate printer
- Bambu Lab P1S - 0.4 nozzle
- Estimate process
- 0.20mm Standard
Indicative estimate for the selected file only, based on the author’s weight and print time. File variants are not added together. The final price is calculated after file analysis.
Saved on this device.
Baby mobile holder (to use with 9 and 18mm wooden rods) and clamp compatible with round co-sleeper bars (Chicco Next2Me)
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 14
- Makes
- 0
- Views
- 151
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Bedroom
- License
- Creative Commons — Attribution
Mobile and connectors:
- Printing: PLA is sufficient, as this is all light weight. 0.2mm layer height, 3 perimeters. I recommend printing the ball caps with 2mm brim and supports on the ledge of the 45degree connector and underneath the hook. Print the rest without supports.
The hook connector has a ball joint and is freely rotating. My tolerance is: holes designed with +0.2mm holes, press to fit works well with my 9mm and 18mm rods.
Wood length recommendations:
- mobile rods (9mm) 10 - 20cm (I did 20cm)
- main holder (18mm) 30 - 50cm (I did 50cm)
- holder arm (9mm) 35-50 cm (I did 45cm).
I attached it with my own design for a ChiccoNext2Me Co-sleeper compatible clamp.
Clamp for Chicco Next2Me:
I recommend printing in PETG for extra stability with at least 20% infill and 5 perimeters and extra solid layers on the bottom and top. I printed it with 0.3mm layer height and 0.6mm nozzle for increased printing speed. I printed mine with organic supports on two points of the sliding ledge for the moving part (see 3mf file).
- extra hardware: M6 nut + M6x60mm bolt with handle (I used this: https://www.amazon.nl/dp/B0D9K8WKQJ?ref=ppx_yo2ov_dt_b_fed_asin_title WYYFXY® 12pcs Knurled Screws M6×60mm Star Handle Screw Metal Star Screw Plastic Strand Head Screw Clamp Knob Black Wing Screw for Industrial Equipment)
After printing, you need to free the moveable part a little bit, insert the nut, then when you start screwing in the bolt from the outside, it will help it loosen the part properly. I recommend tightening it all the way and loosening it again a few times, before using it on the actual co-sleeper. I had quite a few iterations with this, to not have it bend / loosen after a few days. Thus is became a lot thicker and sturdier than the initial design. I hope it works for you!
Extra models provided / links:
- 45degree connector (see this remix: https://www.printables.com/model/1377163-baby-mobile-18mm-to-9mm-45-degree-rod-connector )
- hexa-holder middle: flat hexagon design alternative (not printed myself)
- cat ornament rotating wind spinner (https://www.printables.com/model/1377986-spinning-cat-and-butterfly-ornament)
Fun little (useful) project to do at 9months pregnant! 😂
For balancing, you can either use the rings provided, or like myself use wood beads that have 9-10mm holes in them. (E.g. https://www.amazon.nl/dp/B098T8G56L?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1 PandaHall Natural Round Wooden Beads 20mm Unfinished Wood Ball Spacer Loose Beads for Macrame Crafts, DIY Jewelry Making Home Decor, Hole: 9-10mm, 50pcs).
I highly recommend using a string set up to a top connector as in my design, as it hugely improves the possibility for making it hang balanced and stay balanced even if you touch or move the bed. I could have done with a neater tying job, but in the end could not be bothered anymore….
For the hangers I recommend anything lightweight (no risk of injury). Can be printed (e.g. my cat and butterfly spinning ornament: or whatever safe/lightweight items you want - sew them, or buy them from ikea :) ).
Word of caution/disclaimer:
Please always ensure everything is stable and that there is no risk for danger/injury to your child. I take no responsibility for your prints/their safety during usage. After setting mine up, I left it set up for at least a week to verify, that it does not tilt by itself and remains stable. I recommend never leaving the mobile with your baby hung up unsupervised. The mobile can easily be removed from the hook for nap times.