1 / 5
Meanwell LRS-350-24 housing for Prusawire / Prusa MK4 (S) / Prusa i3 — image 1
1 / 5

Meanwell LRS-350-24 housing for Prusawire / Prusa MK4 (S) / Prusa i3

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Meanwell LRS-350-24 power supply housing with mounting points for Prusa frame

Rating
0 / 5
Likes
5
Downloads
21
Makes
0
Views
185
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

Overview

Full housing for a Meanwell LRS-350-24  power supply (or others with the same housing) that mounts onto Prusa frames with two M4 screws at 117mm distance.

If you prefer a simpler solution, I recommend to use ericbuilds model

Hardware

  • 2x heat set insert M4 short 6.3mm x 4mm (not Voron spec, Voron spec version will follow maybe)
  • 10x heat set insert M3 4.5mm x 6.7mm (not Voron spec, Voron spec version will follow maybe)
  • 8x M3x10mm countersunk screw
  • 2x M3x6mm countersunk screw
  • 2x M3x8 cylinder head screw (M3x10 works as well)
  • 2x M4x12 countersunk screw
  • 2x M4x10 cylinder head screw for frame mounting

Electronic parts

  • 1x power supply Meanwell LRS-350-24 or other with same housing
  • 1x power switch for cutout ~30x22mm (I used Marquart 01835.3105-01)
  • 1x power socket / emi filter TRU COMPONENTS TC-10101436 or cutout compatible

Variants

For now, there are two variants for the lower enclosure part. One with an opening for using a 20mm circumference cable grommet and another one without an opening, so you can apply your own custom opening.

Printing

Preferably use a filament with high heat resistance, such as ABS or ASA, PETG probably also works. Avoid 100% infill since it will lead to more shrinkage and deforming of the part. The lower enclosure needs support on two bridges, organic support worked perfectly for me. All other parts print without supports.

Assembly

  1. Insert the heat set inserts as shown below

    Upper enclosure


    Lower enclosure

     
  2. Optional: If you used the lower enclosure variant with cable grommet cutout, place a cable grommet on the opening. I had a left over cable grommet from either MK4S or Core One build that should fit a 20mm circumference.

     
  3. Slide the lower enclosure part into the upper enclosure part on the two dovetails. Press down on both tails and check that the third, centered dovetail joint will slide into place

     
  4. Place the PSU into the upper enclosure part so that the electrical connectors point towards the opening. Secure the PSU with four M4x12 countersunk screws. Be careful not to use longer screws, those could damage or short circuit internal parts.

     
  5. Install the upper cover using four M3x10 countersunk screws and double check that the vent openings align with the vents on your PSU

     
  6. Install the power switch (click-in-place) and power socket (2x M3x8 countersunk screws)

     
  7. Install the lower cover with two M3x10 countersunk screws at the bottom and two cylinder head screws at the top

     
  8. Mount the whole enclosure on the frame using two M4x10 cylinder head screws

     
  9. Secure the two feet on the lower enclosure backside on the aluminium extrusion of the frame using two M3 nuts and two M3 cylinder head or flat head screws. If you use cylinder head screws, use a washer with each screw.

     

Tags