1 / 4
Linked Helix Fidget (Kinetic DNA Spiral Toy/Art Piece) — image 1
1 / 4

Linked Helix Fidget (Kinetic DNA Spiral Toy/Art Piece)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a series of links that are interconnected to form a spiral when twisted. It prints in place and has 40+ sizes.

Rating
5 / 5
Likes
20
Downloads
93
Makes
1
Views
758
Reviews
1

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — NoDerivatives

Introducing the Linked Helix! 

A fully parametric design that prints flat on the buildplate as a Print-in-Place design, but then with a twist elegantly spirals into a helix. It is made up of a series of links that all freely spin around a central axis, but the “twist” is that as each link turns, after it turns a certain amount, it turns the adjacent links along with it and so on in a cascading effect! This creates a elegant arch that can spin about freely and makes an impressive looking and fun fidget toy. It's also fairly durable! The amount of links and the length of the links can be changed in OpenSCAD to create a diverse ecosystem of helixes that look and feel different from each other, with there also being 40 different pre-generated sizes to choose from! There are also three different types of stands to fit your specific helix needs!

Do you like these helixes and want more? Check out my Premium helix pack at the link below with 1000s of fancier helix combinations!

https://www.printables.com/model/1512382-linked-helix-premium-pack-1-kinetic-dna-spiral-toy

The Helix naming system and choosing your first helix

Here's your complete guide to picking your first helix! First off, explaining the naming system. Every file I provide will start with LH, standing for Linked Helix, followed by the number of links, the length of the links, and then the type of helix it is. The helix type doesn't matter here as all that is provided is the basic Rectangular helixes, but it's an important distinction for the Premium Helix Pack mentioned above. For some sizes I have also included helixes with Extended End Hubs, meaning the center rod of the helix stretches out farther than normal and gives you a place to hold it. Those files will have a +10EH after the link length, where the number(10 in that case) is how many mm the ends protrude out. A filename may look something like LH_40Links_50mm_Rectangular, meaning that the helix is forty links long and each link is 50mm across. Each link can rotate 12 Degrees in either direction before pulling the next link along, meaning it takes about 15 links to do a full 180 Degree spiral. Also, With a longer link length the spiral will appear more “compressed”, like the spiral is tighter, even if the rotation between the links is the same. It's just a neat trick of the eyes :)  This helps give a lot more variety between helix types, so I encourage you to try printing multiple sizes and seeing which you like best! They feel a lot different to fidget with too. I chose to provide sizes only up to 60 Links and 80mm as I felt that was a good stopping point in general, but that's not to say you can't use the parametric OpenSCAD customizer to make one waaaaaay bigger, as long as your printer has a build plate that it can fit on. For your first helix, I recommend printing one that's between 20 and 30 Links, with a 40mm Link Length as I think that provides the best mix of playability and coolness without taking too much filament. And then, if you like the feel of it, you can go back and print a massive one. 

Also, if there's a specific helix size you want(like one bigger than the provided sizes) ask in the comments and I might be willing to render it and upload it for you!

The Three Stands

There are three stand types: The Spinning Stand, the Bottom Clip Stand, and the Bottom Hub Grip Stand.

 The Spinning Stand is a stand that goes around the helix and holds it by the little indents on the two ends, which also allows the helix to spin in the stand and adds a whole new dimension of play with it in the stand, as well as being a great way to display it. But. There are two downsides to this stand, namely that it takes more filament than the other two and that you have to print the correct size to go with a specific helix. For this stand you have to print the one that matches the number of links the helix has, and if there are Extended End Hubs on the helix it also requires a different size for those.(Not provided, but can be done with the OpenSCAD Customizer) Also, it is only compatible with helixes that have a link length of 80 or less. If a helix has a link length of more than 80, it will not fit.

The Bottom Clip Stand is a stand that holds the helix by the bottom two links and nothing else. The advantages are it takes very little filament(only around 7 grams) and is compatible with ANY SIZE HELIX. The disadvantages are that it is a bit wobbly and less stable than the other two stands and it grips onto the bottom TWO links, keeping either of them from rotating. This means that while the rest of the links can turn freely, the bottom two links will not be able to rotate apart from each other. It's not a good stand for playing with the helix, but it works great for sitting it on a shelf somewhere as a display item. It also has a hole in it for an Extended End Hub of up to 10 mm to seat into, which would make it a lot more stable. An Extended End Hub value of more than 10mm will cause the bottom two links to not seat fully, but it will still stay in the stand just fine.

And finally, the Bottom Hub Grip Stand. This stand is a lot like the Bottom Clip Stand except it doesn't grab onto the bottom two links and lets them rotate freely, plus its a lot more stable. The downside is it will only work with helixes that have an Extended End Hub of 10mm or more. If it's less than ten, say 5mm for example, it will still work but it just won't be quite as stable. If it's more than ten, the helix will just positioned farther up in the air instead of right above the stand. (I only provided helixes with extended end hubs for some smaller helix sizes, where they will benefit from them for fidgeting with the helixes in the hand, if you want them on the other helixes you can use the OpenSCAD customizer)

 Print settings and post-processing

Material: I used PLA, although any similar material like PETG should work fine as well.

0.4mm nozzle, 0% infill, and 2 wall lines-the weakest part of the helix is the center of the links which prints solid even with just two wall lines, so there is next to no advantage to adding infill or doing more than 2 wall lines. The only part that gains any real strength is the center rod, which is already plenty strong with the aforementioned settings.(If doing a helix with a very high number of links(like over 100) then you may want to have that center rod print solid)

No supports needed

Make sure you have good bed adhesion as this model has a lot of small parts that need to stick to the bed. Even if the first layer goes down fine, the most frequent point of failure is with the small hubs in between the links as they have a very small point of contact with the bed. For the first 2mm of height before they bridge together and connect, there's a solid chance the nozzle might knock a couple off. If this happens, don't worry. In my experience this doesn't ruin the print and if you let the print finish, it will still work fine. This just leaves a small visual imperfection where the hub should have been, and can(it doesn't always!) make the helix turn slightly worse, but it can still be smoothed out as detailed below.

Use a brim with the Spinning Stand, it really likes to warp.

If you print a helix and it is permanently fused, you can adjust your horizontal expansion(the name will differ slightly based on the slicer) to make the tolerances looser. This design uses a mix of 0.3 and 0.4mm tolerances that most printers can handle though.

After you've printed your helix, congratulations! you now have a shiny slab of plastic! Depending on your printer, all the links may spin great straight off the build plate, or they might be a bit stuck. The result depends fully on your printer! For a worst case scenario, here's your ultimate guide to freeing up a stuck helix! Step 1: We need to make sure the links aren't fused to adjacent links. Take one end of a link, starting at one of the ends of the helix, and bend it slightly away. Your goal is to make sure it's not stuck to the link next to it in any way. If it won't flex away, it might be stuck and you need to stick something between them(like a flathead screwdriver) to force them apart. Repeat this for every link, on both ends of the link. Step 2: We are now going to break the center of each link free, one by one. Again, start at one of the ends of the helix. Grab a single link, and twist it sideways slightly. Your goal is to break it free from the center hubs/rod it spins on. Remember it is connected to the adjacent links so if those links are still stuck it will only rotate SLIGHTLY before it is stopped. Your only goal is for it to be broken free from the central hubs/rod, so if it can turn slightly in each direction then it's free and you can move on to the next link. Freeing up the last link can be a lot harder as with all the other links freed up, there's no good place to grab it if you need a lot of force to free up the link. I really don't have a solution for this, just keep trying to twist that final link free if it's stuck! You will know the helix is free if you can turn the central rod by the hubs without any links turning with it. Remember that with a semi-decent printer, you don't need to do this and all links can be freed up easily with a slight twist.

Now, to break in your helix for the smoothest spins!

First off, if you want to get a good baseline idea of how well the helix turns overall, try turning the center hubs and feeling for any resistance/friction. You don't need to turn it by the ends, instead "roll" it with your fingers by the hubs that are in between the links. This also provides another way to fidget with your helix :) Now, to get your helix to the best it can be, your goal is to rub the rough 3d printed parts together to smooth them out. To do this, grab 10 to 15 links on one of the ends of the helix while holding the other end of the helix with your other hand, and then turn them while both pulling away AND bending them at a slight angle. If you can hear the plastic gripping and making a bit of a grating noise, then you know it's working. Keep rotating them back and forth until either you can't feel it rubbing on itself anymore or until the helix is as smooth spinning as you want it. Make sure to do this for both ends of the helix! In my experience trying to do this with the links in the middle doesn't really work much, and just breaking in the ends makes the whole helix spin MUCH better even without doing anything to the links in the middle. 

Congratulations! You made a helix! if you enjoyed this model, I would appreciate reviews, makes, and feedback!

Using the Customizer

This section is on using the OpenSCAD customizer to make your own helix! If you do not have OpenSCAD, this model is also available on Makerworld and you can use the customizer there. Note that it is a complex model and helixes with a higher number of links can take 20+ minutes to render. With that out of the way, here's all the variables you can adjust!

The $fn value adjusts the resolution of the cylinders of the model. I turn it to 100 for printing, but for testing out different helix variables in OpenSCAD it loads a LOT quicker if you turn it down to a lower value like 30.

The Helix Link Number adjusts how many links are in the helix. Each link is 3mm wide, so ten links is 30mm long and so on. For a complete 180 degree twist with the default rotation between links, it takes about 15 links for a full rotation of the links.

The Visual Link Rotation adjusts the visual rotation of the links, this is for visuals in OpenSCAD only and does not adjust the actual amount the links can rotate when printed. This is just to get an idea of what it will look like when twisted after printing. Set this value equal to the Rotation Between Links to get an idea of what it will look like. Set to zero before exporting and printing.

The Link Length Diameter affects how long the links on the helix are. This number is in mm and is the total length of each link. A longer link makes the helix's spiral look more "compressed" despite it not actually affecting how much the links can rotate. To get a better idea of what it looks like when rotated, use the "Visual Link Rotation". Do not set this lower than 18mm.

The Extend End Hubs makes the hubs at the two ends of the helix longer, which can make it easier to hold and spin by the ends. Each number(example:1) adds 1mm of length to each end hub, making them protrude out that distance. The Free spinning stand also has a matching variable that has to be adjusted for this to still fit. 

The Rotation Between Links this value affects how far each link can rotate before being stopped by the adjacent links. The number is in degrees, so at 12 each link can rotate +- 12 degrees in either direction. A higher value will lead to a tighter twist, and vice versa. The max value this should be put at is 12.5, there is not enough vertical room to put it higher than that unless the Linking Nub Thickness value is lowered.

The Linking Nub Thickness controls how thick the nubs in the links that carry over the rotation are. I HIGHLY ADVISE leaving this setting alone unless you know what you are doing and want to experiment. The number does not correspond to any particular unit of measurement, but a higher one will give thicker nubs and a smaller one will give thinner, and therefore weaker, nubs. A smaller value can allow the Rotation Between Links value to be increased slightly further.

The Spinning Stand also has its own customizer. You have to set the Helix Link Number and the Extended End Hubs value equal to the helix you want it to fit. Note that most helixes uploaded by me will have the Extended End Hubs at 0, unless otherwise stated in the file name.

Extra notes

This section is for any random extra bits of information that don't fit in elsewhere!

First off, are you curious if this model would work at all in TPU? So am I! If anyone out there prints in TPU and is feeling adventurous, I would love to find out how it compares to a normal PLA helix!

Do you want to sell these helixes commercially? if so, I grant you permission to do so ONLY IF you purchase the premium helix pack(available on the Printables Store at the link above). For just $8, you can have the commercial rights to sell these helixes!

If you have any questions or need help with anything, ask in the comments!

Tags