1 / 8
Prairie Schooner - Pivoting F. Axle - Pioneer Covered Wagon,  ~1/15th Scale — image 1
1 / 8

Prairie Schooner - Pivoting F. Axle - Pioneer Covered Wagon, ~1/15th Scale

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a ~1/15th scale Prairie Schooner style covered wagon with a pivoting front axle and hinged tongue.

Rating
0 / 5
Likes
7
Downloads
71
Makes
0
Views
265
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

The Version 1 of this Prairie Schooner covered wagon (without the bonnet) has a fixed front axle, 

which is fine for displays, but not as fun to play with. This Version 2 has a pivoting front axle attached to the tongue (with a print-in-place hinge, which allows the tongue to pivot up and down). Pivoting the tongue side-to-side will also pivot the front axle. This allows the wagon to be turned easier. Since many of the components of this model differ from Version 1, I decided to post this as a separate model.

NOTE:     In order to incorporate the front axle with the tongue, and allow this assembly (Tongue and Front Axle Assembly) to be able to be printed on the majority of 3D printers, I shortened the Tongue from Version 1, and redesigned it to accommodate a fairly strong hinge system. With a fully assembled length of ~380mm, this Version 2 model is about 25mm shorter than the Version 1. I also made the harness loops/rings on the tongue larger and more sturdy (more usable).

NOTE:     The wheels, bonnet bows and hub caps are interchangeable between Versions 1 & 2, but the rest of the components are not – they are version specific.

The model can be printed without any supports. I recommend printing with a 0.4mm nozzle, 0.20mm layer height, and 100% infill. Some components print better with a brim (use your discretion).

COMPONENT PRINT LIST:

  • 1 - Carriage

  • 1 - Axle Stop Bushing

  • 1 - Tongue and Front Axle Assembly

  • 1 - Axle Pivot Post

  • 1 - Rear Axle

  • 2 - Front Wheels

  • 2 - Rear Wheels

  • 4 - Hub Caps

  • 5 - Bonnet Bows

ADDITIONAL PARTS:

  • 10 - 4mm x 16mm self-tapping screws  (purchase)

ASSEMBLY INSTRUCTIONS:

  1. Review the included Exploded Diagram graphics and compare those to your printed components.

  2. All under carriage components are attached to the Carriage by the screws which go down through the Carriage bed and screw into the components. It is helpful for aligning components to first drive the screws through the Carriage bed so that they protrude a little (2-3 threads) out the bottom side of the Carriage. 

  3. Using three screws, attach the Axle Stop Bushing to the underside of the Carriage.

  4. Turn the carriage upside down, and place the Tongue and Front Axle Assembly in the Axle Stop Bushing, so that the beveled ring faces away from the carriage (when the wagon is upright, the beveled ring will face down).

  5. Insert the Axle Pivot Post into the circular hole of the Tongue and Front Axle Assembly, and using a straight slot screwdriver in the slot of the Axle Pivot Post (to hold it in place), drive a screw down through the bed of the Carriage and into the Axle Pivot Post; tighten until snug.

  6. Position the Rear Axle so that the cross shaped supports are touching the bottom face of the Carriage, and with the holes aligned with the rear holes in the Carriage bed; attach the Rear Axle to the underside of the Carriage with two screws, driving them down through the bed of the Carriage and into the Rear Axle receiving holes.

  7. The Wheels - Front & Rear print with the outside faces facing up on the print bed. The Wheels and Hub Caps have corresponding beveled edges that act as a bearings or sorts. Place the Carriage assembly on its side, resting on the opposing axle faces. Place a Hub Cap into a Wheel and align them with an axle screw receiving hole (making sure that your are placing the larger Wheels - Rear on the rear axle, and Wheels - Front on the front axle). While holding the Wheel and Hub Cap in place against the axle face, with the screw holes aligned, screw in one screw into the center of the Hub Cap and into the axle, securing the Wheel to the axle. Positioning the parts this way helps the screw to go in fairly straight. There is no need to over-tighten the screw, but it should be tightened snuggly. The Wheel should spin ~freely. If not, there may be some printing debris that needs to be cleaned/sanded, or the screw may have been screwed in crooked or with too much force.

    • NOTE:     the axle portion of the Hub Caps is slightly wider than the width of the Wheel hub, so that the wheels spin freely when the hub screws are tightened.

  8. Repeat the previous step for the rest of the Wheels.

  9. Insert the 5 Bonnet Bows into the receiving sockets on the sides of the Carriage. The bottom forked tips of the Bonnet Bows are designed to straddle the sides of the Carriage, with the outside forks fitting in the outside sockets on the Carriage side walls, and the inside forks fitting down the channels on the inside Carriage walls.

NOTES:

  • As with the Version 1 model, this model was designed to look somewhat realistic, but it was not designed to be a scale replica. It was designed using generalized measurements and photos of wagons. Actual wagons have many additional parts and mechanisms that were not needed to be included in this model.

  • I did not design a ‘bonnet’ - the traditional canvas covering for weather protection. If I do make a bonnet sometime, it will likely be made of a cloth material, not 3D printed. However, I did design in hitching pegs/posts/hooks/fingers (I don't know what to call them) that protrude out of the bottom sides of the bonnet bows, where a bonnet can be attached.

 

Tags