Dual Unifi G6 Turret Wall Mount for 180° Coverage
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A part to mount 2 ubiquiti g6 turrets (100 mm ø) on a wall to provide 180° view
- Rating
- 0 / 5
- Likes
- 8
- Downloads
- 37
- Makes
- 0
- Views
- 697
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Photo & Video
- License
- Open Community License v1
This is a custom 3D-printable mount designed to hold two G6 turrets (each with a 100mm diameter) against a wall, providing 180° coverage. It's ideal for security camera setups where you need wide-angle monitoring. The mount features an open design for easy pigtail access. I've included protective covers to prevent debris from reaching the cameras through the mount body.
I printed the covers in TPU, they take a bit of effort to snap into place, but it's straightforward and secure. The main body was printed in PETG, which experienced minor warping during printing, but it wasn't severe enough to impact functionality nor printing. Note that the built-in top slope (intended to direct rainwater away from the wall) didn't hold perfectly due to the warping—adding a bead of caulk along the top edge after installation is recommended for better weatherproofing.
No supports were needed for printing, making it a relatively easy build. I've included images of the printed parts, assembly, and installation to help visualize the process.
Features
- Mounting: Secures to concrete walls using four #12-16 button-head screws with plugs. The lower holes are threaded for better screw compression and grip. The top two use blind keyhole slots, to prevent water ingress. Set these 2 screws to protrude about 4mm for hanging.
- Camera Attachment: Uses the included self-tapping screws from the G6 turrets. I recommend adding a drop of Loctite to each for added security.
- Template Included: A separate template piece helps with alignment, incorporating two bubble levels (from the camera included install kit). Use it to mark and drill pilot holes (3mm suggested). My plugs were ¼", so you can enlarge the holes to match your hardware. Note: The final template differs slightly from early images, as I added a second bubble level for improved accuracy.
- Weather Considerations: Sloped top for rain runoff, plus optional caulk for sealing.
Printing Recommendations
- Material: PETG for the main mount (durable but watch for warping—print at lower speeds or use an enclosure if possible). TPU for the protective covers (flexible and resilient).
- Settings: No supports required. Added a brim to improve bed adhesion. Also used VLH
- Issues Encountered: Minor PETG warping, but functional. The keyhole slots needed a little heat to reduce stress and allow the screws to slide. No other major problems.
Assembly Instructions
- Print all parts from the 3MF file. Auto-orient should work fine. You should end up with 4 pieces from the single file. Don't print as is
- Mount the holding rings from the cameras, using their self-tapping screws with a dab of Loctite
- Pass the pigtail from the camera. I attached an ethernet cable as to not lose the cable in the body.
- I placed the half of the cover without the ridge towards the rear of the body, and they pushed the other half into place
- Afix the camera and tighten the set screw. If you need, connect the cameras to adjust. Might be easier on the ground.
- Drill and install the top right screw on the wall. Use the template for the other holes. Spin the bubble levels, until both show the same angle, they stuck a little. You can use tape to hold the template in place once aligned
- The template has a guide for the drill bit (3mm), and you will drill through these. Use the template to drill the pilot holes.
- After the pilot holes, Drill holes adequate holes for your screw's plug. Clean the holes and insert the other 3 plugs
- Install the top two #12-16 screws into wall plugs. Leave about 4mm between the wall and the bottom of the screw head.
- Optionally, apply caulk to the top slope for better water resistance
- Mount the body, sliding the screws into the keyhole slots. Screw in the two lower screws.
Added a shim model in case you want to align the cameras on a bench-top. This matches the inclined upper surface and has a notch to match the middle drain of the camera's body
_______________________
v2 after trying to insert the capped pigtails, found it was a tight fit. Increased the window size a little to make it easier