Star Wars F's Lightsaber
We calculate the final price from your selected file. You review and accept it before payment.
Estimated printing price per file
€0.12 – €0.15 net (excluding VAT)
For file: lightsaber-f5 silver red_0.2mm_PLA_MK3S_10m.gcode
This is an estimate for one file. You’ll confirm the exact price before ordering.
File and estimate settings
File used for this estimate
Average indicative estimate: €0.14 excluding VAT (range midpoint).
- Weight reported by the author
- 1 g
- Print time reported by the author
- 10.2 min
- Source material
- PLA
- Estimate material
- PLA
- Estimate printer
- Bambu Lab P1S - 0.4 nozzle
- Estimate process
- 0.20mm Standard
Indicative estimate for the selected file only, based on the author’s weight and print time. File variants are not added together. The final price is calculated after file analysis.
Saved on this device.
Model of F's Lightsaber from Star Wars: Visions with collapsing blade
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 37
- Makes
- 0
- Views
- 226
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Props
- License
- Creative Commons — Attribution
This is my fourth model of F's lightsaber from Star Wars: Visions, now updated to match the new short “The Lost Ones”. Its earlier appearance was in “The Village Bride”.
It has a collapsing blade.
The hilt can hold a small flashlight. It can fit flashlights that are 12mm-21mm in diameter and less than 70mm in length.
The emitter can open and close. The blade cannot extend while the emitter is closed.
Dimensions (Hilt)
Length | Width | Depth |
|---|---|---|
322mm | 74mm | 41mm |
Print Instructions
Hilt
Everything wass printed at 0.2mm layer height unless stated otherwise.
Part | Copies | Color | Additional Settings |
|---|---|---|---|
upper emitter | 1 | silver | ironing, supports on builtplate |
inner emitter | 1 | transparent | supports on builtplate |
lower emitter | 1 | silver | ironing |
upper hilt | 1 | black | supports on builtplate |
button | 2 | silver, red | filament change at 4.8mm |
knob | 1 | silver |
|
upper switch | 2 | blue |
|
hilt silver long | 2 | silver | supports on buildplate |
hilt silver medium | 2 | silver | supports on buildplate |
hilt silver short | 2 | silver | supports on buildplate |
middle hilt | 1 | black | supports on buildplate |
hilt blue | 2 | blue |
|
lower hilt | 1 | silver, black | lower layer height |
lower switch | 2 | blue | filament change at 27mm, ironing between 26mm-28mm |
pommel | 1 | silver | lower layer height, ironing |
The inner emitter can use transparent yellow or transparent colorless filament.
Blade
The blade is printed in vase mode. You should use transparent yellow filament.
While printing, the parts will start to wobble as they get taller, reducing the print quality. This can be partially counteracted with good bed adhesion, using a brim and reducing print speed. There will still be some wobble, so you might have to print some parts twice to get a better quality.
You can either use a long blade (6 segments) or short blade (5 segments).
Everything was printed in vase mode, with 0.2mm layer height, 0 bottom layers and 8mm brim.
The print speed was gradually reduced during the print. (I did this manually because I was unable to do this in the slicer.)
Curved Blade
The "default" blade for this model is straight. If you want a curved blade instead:
Do not print the blade from this model.
Instead print the blade from the previous iteration (link).
Do not print the following parts:
upper emitter, inner emitter, upper hilt, middle hilt
Instead print the "curved"-variants listed in the folder "Curved" (same colors and settings as the "default" variants listed in the table above)
lightsaber-f5 curved upper emitter
lightsaber-f5 curved inner emitter
lightsaber-f5 curved upper hilt
lightsaber-f5 curved middle hilt
If you want to use the pre-sliced files:
Instead of the files in the folder "Blade", print the blade from the previous iteration (link).
Instead of "lightsaber-f5 silver[...].gcode", print "lightsaber-f5 curved silver[...].gcode"
Instead of "lightsaber-f5 black[...].gcode", print "lightsaber-f5 curved black[...].gcode"
Instead of "lightsaber-f5 transparent[...].gcode", print "lightsaber-f5 curved transparent[...].gcode"
Assembly
The following render shows how all pieces fit together. A purple arrow means that the pieces are supposed to be glued together. Where there is a green arrow, no glue should be used.
The upper switches are glued only to the lower emitter. They are not glued to the upper hilt.
UPDATE [2026-03-23] Re-added the curved blade
UPDATE [2026-03-27] Added pre-sliced files for the curved blade
If you want to support me, you can do so via this link: https://ko-fi.com/printingdaniel#