1 / 18
Silent RV Cooling: Noctua Fan Flex-Mount with PWM Wall Controller — image 1
1 / 18

Silent RV Cooling: Noctua Fan Flex-Mount with PWM Wall Controller

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Custom-designed mount to position a 140mm Noctua fan using a Joby Gorilla arm.

Rating
0 / 5
Likes
2
Downloads
2
Makes
0
Views
94
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

Bring cool, quiet airflow exactly where you need it!
This custom-designed mount lets you position a Noctua fan using a Joby Gorilla arm, while a PWM speed controller neatly integrated into the wall bracket gives you full control over airflow and noise levels.

I created this setup for my caravan/RV to keep air circulating during hot days — and even at night — using the famously quiet Noctua fans. The flexible arm allows you to direct the breeze wherever it’s most effective, whether that’s toward a bed, seating area, or ventilation point.

Features

✔ Fully adjustable thanks to a Joby GorillaPod-style arm

✔ Integrated PWM controller in the wall mount for easy speed control

✔ Perfect for caravans, vans, RVs, boats, or small rooms

✔ Designed for 140mm Noctua PWM fans (NF-A14 PWM)

✔ Designed for silent nighttime operation

✔ Clean, compact, and easy to install

Printing Notes

Recommended material: PETG or ABS for heat resistance (especially in RVs)

Use “Arachne” wall generator, not to eliminate the “break-away wall” (blue face as on the screenshot) unintendedly. ("Classic" will simply not print the thin brake-away wall.)

Printing orientations:
  • The top part with the handle should be printed flat (on the handle). 
  • The lower part should be printed standing(!) for maximum strength (when adjusting the fan orientation back and forth, a considerable amount of force will be exerted via the ¼" screw). Make sure to orient the part that the “break-away wall” is on the lower side. With this, it can function properly as an integrated support.
  • The wall mount with the rear facing up.
  • The Joby cable clip flat of course.

BOM

  • Noctua NF-A14 PWM (The black or the brown one)
  • Two Noctua fan grille, NA-FG1-14
  • Joby GorillaPod Arm
  • PWM speed controller (See screenshot, 4-pin with PCB size 24mm x 19mm. E.g. find on Ebay under “12V 1 Channel PWM DC Fan Speed Controller Motor Module Switch” https://ebay.us/m/DKwY9M or similar. It's the one with the 4-pin header oriented sideways. You will need to desolder the potentiometer for use with my wall mount.)
  • PCB screw terminal pitch 2.54mm, 2pole, (e.g. DG308-2.54-02P-14-00AH)
  • A short piece of ribbon wire or five short single wires.
  • Two ¼"-20 thread heat inserts
  • Four M2.5 x 40mm cylinder head bolts
  • Eight M2.5 washers
  • Four M2.5 nuts (safety nuts are advised) 
  • i.a. Locktite or similar

Assembly

Fan Mount:
  • Follow printing orientation advice from above. 
  • Insert the heat inserts from the “inside” (the side facing the fan) towards the outside.
  • Attach the 4-pin power extension cord and all eight anti-vibration pads (included in the Noctua fan shipment, usually).
  • Place both fan grilles and snap the upper (handle) part in place, essentially sandwiching both grilles and the fan. The handle is on the intake side. Orient the fan to have the power cord outlet at the top right corner and make sure the cables run below the handle part. The connector should neatly fit inside the gap of the handle part.
  • Break-away the “break-away wall” using small pliers or so.
  • Feed the remaining cable below the lower fan mount part and through the opening of the "break-away wall".
  • Snap in the lower fan mount, similar sandwich style
  • Mount all four M2.5x40mm screws incl. washers and nut. The screws give the cable some hold as well.
Wall mount:

This is a little bit quick and dirty - and its made for the described PWM controller only. So yeah.. Feel free to design your own mount and share it.

  • Insert the heat inserts from the “inside” (rear side) towards the outside.
  • De-solder the poti and clean the PCB holes.
  • Solder the ribbon wire or single wires to the five terminals of the PCB.
  • Solder the 2.54mm screw terminal to the +12V and GND input pads.
  • Insert the PWM controller into the slot.
  • Insert the poti and secure it with the nut
  • Fiddle the wires towards the poti and solder them to the appropriate pins.
Final assembly:
  • Use the Joby arm to connect both parts. You may want to add some Locktite to the ¼" threads to avoid opening the thread when the weight of the fan is hanging to one side.
  • Connect the 4-wire cable and secure it with some cable clips.

Why I Made This

RV interiors can get stuffy fast, especially in hot weather. This adjustable cooling setup helps create gentle circulation without adding noise, bulk, or permanent fixtures. It’s been a game-changer on warm nights!

The fan mount was mastered a six-week trip through Portugal and Spain, and I can proudly say it worked like charme. Enough power for the day and ultra silent operation during night.

Tags