Frame counter for Fat Shot 617 panoramic film camera
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Optional upgrade for a 3D printed film camera Fat Shot 617 that adds a frame counter to the top of the cassette
- Rating
- 0 / 5
- Likes
- 20
- Downloads
- 94
- Makes
- 0
- Views
- 656
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Photo & Video
- License
- Creative Commons — Public Domain
This is an optional upgrade for Fat Shot 617 - Medium format 6x17 modular panoramic film camera. It replaces the top part of the cassette and adds the mechanism that displays the frame number the camera is currently shooting.
WARNING: Be aware that this model is an overenginered bunch of small parts, and given that FDM printing can be very inaccurate at this scale, the assembled model can require some additional post processing like filing, cutting and drilling to be assembled and to work as intended.
How it works
Frame counting is done with a flat cam that rotates at about 1/5th rate of a take-up spool, and a follower, which translates the motion to the dial. The cam is a flat disk with a continuous groove, like a record, the shape of which determines the exact points where the follower jumps to the next frame.
The mechanism is more complex than a simple reduction mechanism with an indexing, because accurate frame counting has to take into account the changing diameter of the take-up spool as the film winds onto it. With each new frame, the number of turns needed to advance a full frame becomes smaller.
After reaching the last frame, the cam is stopped at the predetermined position so it can be restarted at the same point every time at the start of a new roll. The belts slip until the cam is released using a lever on top.
Here is the video that shows the action:
Recent updates
2025-11-30:
Added a pdf along with an svg file for a dial in case there are problems with fonts.
2025-11-29:
Added a slot on the cassette top to make it compatible with the latest version of the camera in the main project. If you have already finished printing the previous version, these parts will need to be reprinted:
Cassette Top
Spool Flanges Left and Right
Reuploaded all files to have more consistent and overall better naming. No changes were made to the models themselves.
Added an instruction on delaying the reset to prevent the first frame from being cut. See the “warning” in the “How to operate it” section.
2025-11-25:
Updated the follower model to beef it up a bit and elongated the arm that stops the cam to delay the first frame.
How to operate it
Reach the 4th frame by turning the knob on the camera or by pressing and moving the lever all the way towards yourself, and then make 5 full turns of the take-up spool for the cam to reach the stop. If you advance the film normally, this stop will be reached long before you wind all the film on the take-up spool, so it basically happens automatically.
Load a new spool and advance the film to the point when the index arrow is seen through the small window in the rear of the camera.
Press the lever and move it all the way away from yourself. This resets the counter and synchronizes the counter mechanism and the film.
Use the dial on top to know where to shoot each frame.
- When the dial starts to move, it means that the previous frame was 100% cleared with about 10-20mm extra space.
- When the dial stops and shows the full number, you reached the optimal position for this frame.
WARNING: Different manufacturers make their film differently and the distance between an index arrow on the backing paper and the start of the film itself can vary. This mechanism shows the frame #1 a little on the early side which is, for example, perfect for rolls of Lucky 100, but it cuts the first frame by about 30mm for Kodak Gold.
So, when you use a film for the first time, pay attention to where exactly the frame switch occurs on the dial while advancing to the first frame. It should happen between the numbers 2 and 3 in the rear window.
If the switch happens too early, remember how many more turns of the knob are needed to pull the film to the correct position. The next time you use this particular film and reach the index arrow, turn the knob by the same amount before resetting the counter to delay the reset and prevent the first frame from being cut.
Here is the video that shows how to use the Fat Shot 617 with a frame counter installed:
BOM
M7 washers - x2
17 mm steel rods 3 mm in diameter - x4
6 mm steel rod 3 mm in diameter that should be sharpened to a cone with a 45-degree angle. Don't make it pointy though, leave a blunt tip so it won't dig into the plastic.
Rubber O-rings 3.5 mm thick 31-33 mm inner diameter - x2. These are used as belts in belt driven reduction mechanism.
M3x14 screws - x4. Round head needed as there is not enough space for a cylindrical head.
M3x25 or M3x30 screws - x2
M3x8 screws - x8
M3x5 screw - x1.
Silicon grease
Compression spring at least 10mm in length and 7mm inner diameter. I used 7x12.5 spring with 0.5 mm thick wire and found it to be a good balance between the ability to hold the follower in place and the resistance it creates. This spring can't be too stiff because it can press the follower too hard against the cam and make the belt slip when it shouldn't.
Printing tips
I desined everything to be printed using PETG with 0.6mm nozzle and 0.25 mm layer size. But I recommend to print the cam profile or the whole cam part with 0.1mm layer size. Many dimensions are made multiples of 0.6 horizontally and multiples of 0.25 vertically, just as the Fat Shot 617 camera itself, but I think that standard 0.4 mm nozzle and 0.2 mm layer size would probably work great anyway. PLA could also work and probably even work better, because parts don't need to be flexible and some will even win from more stiffness, like the follower.
Two models need supports - Cam and Clamping bracket for the follower. No supports needed for other parts.
There are two versions of the top lid, only one is needed:
Clear, so you can add whatever you want or use it as is.
With Fat Shot 617 logo and markings: “F” for “Frame number” and “S” with an arrow for “Towards starting position”.
Assembly instructions
During assembly apply grease to all touching surfaces in the process, but make sure no grease gets into the grooves of the pulleys or onto the o-rings! Use isopropyl alcohol to clean up the surfaces if needed.
Cut the steel rods to the required lengths.
Taper one end of the 6 mm rod at 45 degrees. It can be, for example, clamped in a drill chuck and filed using a file or an angle grinder. Again, leave a blunt tip.
Press the sharpened steel rod into the follower with a sharpened end facing down. Flat end should be flush with the top part of the follower arm and not protruding. If the fit is too tight, drill out the hole or use a round file. Glue this part in place if the fit is too loose.
Attach the button to the follower using an M3x5 screw. Follower should look something like this:


Press the other steel rods into 4 holes in the bottom of the frame:

The distance between the bottom surface of the cassette top and the top of each rod should be 17 mm. Use calipers to measure and adjust its positions.Unscrew the dark slide frame from the cassette and remove the existing top part of the cassette if it was assembled before.
Screw the cassette top onto the cassette bottom using middle three of the five holes.

Assemble the flange that sits above the take up spool, using M3x14 screw and M7 washers like this:


Tighten the screw lightly. Pulley shoud rotate freely without much resistance.Attach both flanges to the cassettet top with 3 M3x8 screws each.
Mount the cam and the second pulley on two rightmost rods, holding one of the O-rings in grooves between them.
Put the second O-ring onto the rightmost two pulleys. At this point the assembly should look something like this:

This is a good time to apply grease to the grooves on the top face of the cam.
Place the spring onto the bump in the cassette top between the left rods.
Place the follower on the second rod from the left with the corresponding bump placed onto the spring
Clamp the follower with the included bracket, securing it with two M3x8 screws.

Mark the numbers on the dial with any method you want. You can print the included file and glue the numbers or even draw them with a sharpie. You can do it now or later with the latter option having a perk of being able to mark the correct positions through the window in the lid.
Mount the dial onto the leftmost rod so the gear teeth mesh exactly as pictured below.

Snap the lid on top of the assembly. Make sure it is fully seated onto all the steel rods. Notice that there is a snap-fit joint along the whole length of the back side.

Screw the top with the remaining two long screws using outermost holes.