1 / 1
1/35 CM-21 APC (Taiwanese Variant of M113 APC), an RC Tank — image 1

1/35 CM-21 APC (Taiwanese Variant of M113 APC), an RC Tank

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

1/35 CM21 APC (Taiwanese Variant of M113 APC) RC, tracked

Rating
0 / 5
Likes
63
Downloads
283
Makes
0
Views
2,158
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

This is a rough description, I just wanna upload it soon. The tolerances were adjusted to my printer and local brandless filaments. Please proceed with doubt.

Features:

  • Working tracks and torsion suspensions

  • Openable gate

  • Turret modification requires only a few cosmetic swaps, and motorised turret modification

  • Firmware available

 

*Be sure to check if you can make the brass bushings
*I recommend printing “track link 10” and check if your wire can fit, proceed if they work or if you can change the filament flow setting to make them work.

 

Non-printed component requirements:

  • N20 motor x2

  • M2 8mm machine screws x16 (for wheel axles and tensioner)

  • M2 20mm(for sprocket axles and gear axles

  • M2 8mm screws x11

  • brass tube 3mm outer diameter 2mm inner diameter, 6mm x2 (gear bushing), 13mm x2 (sprocket bushing)

  • iron wire 0.5mm diameter, 20cm x10 (torsion spring suspension)

  • 0.5mm diameter wire (for track pins, front shield hinge, and gate hinge, I use electrical wire)

Tools:

  • To make the brass bushings you may need a Dremel or a power drill, also files and sand papers

  • 2mm, 3mm, and 4mm drill bits to clear the holes on the wheels, gears, and swing arm tunnels

  • Plier and cutter to make the torsion springs and insert track pins

My electronics solution:

  • Seeed Studio Xiao ESP32C3 x1

  • DRV8833 motor driver

  • lMS1117 3.3V

  • ceramic capacitor on each motor

  • 14500 li-ion battery x2 in a AA battery holder

Firmware: Github

Build Details:

Hull: cut supports away and use heat to remove stress marks. Clean the swing arm tunnels with a 4mm drill bit.

Torsion suspension: use the wire bender

  1. cut 20cm wire

  2. insert 2mm metal rod (drill bit will work) to the hole on top of wire bender 1 

  3. insert the wire to the hole next to the rod 

  4. bend left for left springs, right for right springs

  5. insert wire bender 2, hook the wire with it and start winding, 20 turns

  6. bend the end up with plier

  7. put the spring into the trench, it measures the distance between the end hooks

  8. bend one hook down, the other end left for left springs, right for right springs (hook facing you)

  9. trim hooks to under 4mm 

     

Turreted CM-21-A2 prototype mod:

Non-printed component requirements:

  • SG90 servo x1

  • SG90 servo continuous rotation mod x1

  • SG90 arm x1, 5mm-flange-head screw x1, mounting tab/shaft screws x2 (those comes with the servo)

  • M2 8mm machine screws x2 (for mounting turret controller to the hull)

  • M2 8mm screws x8 (mounting servos, turret controller)

  • M2 8mm countersunk screws x2 (for mounting the turret *1)

  • Small O-ring/rubber band x1 (around 15mm in diameter

My electronics solution:

  • mini360 voltage regulator (LMS1117 5v could work? it's not using much current after all)

  • single cell AA battery boxes x2 (for 14500 li-ion batteries)

Build Details:

For a purely cosmetic unpowered turret, print the unpowered turret clip and unpowered bushings in "turret acc 2.3mf", ignore “turret control.3mf”. No O-ring/rubber band needed.

The batteries can sit on either side of the hull (see pic below).

Turret installation:

  1. Install bushings, gun, and shaft to test fit

  2. Make sure gun rotate with minimal friction by sanding, trimming, lubricating these parts

  3. Take them apart, slide the O-ring/rubber band into the slit on the gun

  4. Put the turret onto the roof

  5. Pull the O-ring/rubber band out and hook it onto the groove on the turret clip and screw on the turret clip

  6. The gun should go up. If it gets stuck when you push it down and release, repeat step 2

Controller: screw on the two mounting machine screws to the hull (bottom right in the pic), leaving 3+mm space so the whole controller assembly can slide  and clip in from the front, then fasten the screws. It allows easier installation without taking apart the vehicle. It sits 7.5° in the hull as intended.




Update notes:
v2 archived
v3 is up
Turret mod up
New screwless motor clamp allows mounting electronics and not blocking screws
Arduino firmware release

Tags