Nissan Frontier Utilitrack 50cal Ammo Can Hanger
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Nissan Frontier Utili-track 50cal Ammo Can Hanger
- Rating
- 0 / 5
- Likes
- 7
- Downloads
- 24
- Makes
- 0
- Views
- 490
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Automotive
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Description
This is a set of brackets that allow you to mount a plastic 50cal ammo can (Harbor Freight) to slotted steel hangers to hang from Nissan Utilitrack and maybe others with different track mount hardware.
Currently I have a cheap roll-up tonneau cover, but the idea of these is to allow the boxes to hang below the track so that a flush mount tonneau can be used with them.
There are holes in the brackets to support the use of elevator bolts or maybe furniture feet to stablize the ammo can against the side of the truck bed.
Printing
I printed in ABS with pretty standard settings .4 nozzle, .2 layer height, with a brim.
I designed sacrificial skins to allow the washer recesses to print without supports, but the bridging is ugly; it's behind washers. You could also print with supports.
I designed little grooves on the printing surface side to help break up the straight lines. I find this reduces warping with the ABS on these straight edged parts. I still used a brim.
Notes
I can't imagine I'd put too much heavy stuff in these. Time will tell how well they hold up.
I printed two of these and each time I enlarged the holes for the 1/4" bolts. I printed in ABS and the shrinking on the alignment plug inserts on the inner and backing parts plus the printing seams made the bolts fit too tight. I got them installed just fine, but the models posted here are slightly larger than what I used in hopes that the 1/4" hardware will fit better.
Instead of the 3/8" mounting bolts, I like the knobs, but the store only had one as you can see in the picture. The knobs are a little thick and interfere with the lid opening; however, the plastic ammo can lid flexes, and they allow it to be removed without a wrench.
I listed the 3/8" mounting bolts at 1 1/2" length and that is about the max for the side rails. The rear rails are not as deep, at least on my truck. Shorter bolts would be needed for the rear rail. Given the amount of trouble I had sliding on the spring nuts past the rail mounting bolt heads, I suspect to put them on the rear the spring on the spring nut may need removed. Shorter bolts may be appropriate on the side rails too, as they only really need to be long enough to fully engage with the spring nut.
I bought 2" elevator bolts for the stabilizer feet, and that is about the perfect length for them to be screwed all the way in. And I am using 4" magnetic part trays behind a couple of them, which has them almost screwed all the way in. However, on the ones that don't have those trays behind them, depending on the mount location, they may need to be a bit longer. I suspect 2" would be ideal for the rear rail. And if I had to guess on the right length for the sides without anything behind them, I'd try 2 1/2".
Assembly
Use the drill guide to mark and drill out mount holes on the side of the ammo can with a 3/8 drill bit.
Use a pipe deburring tool or utility knife to clean and very slightly widen the ammo can 3/8 holes.
The inner part goes into the holes from the inside with the thicker portion at the top.
The outer part goes on the outside of the ammo can.
The slotted steel hanger goes in between the outer part and the backing part.
The backing part goes behind the slotted steel.
Feed the bolts in from the back to the inside. Put washers on both sides.
Put a lock washer and bolt from the inside.
The 3/4" bolts go through the very top hole to add rigidity.
For the stabilizer feet, insert a 3/8" nut in one of the available 4 slots.
Load the elevator bolt with a 3/8" nut, lock washer, and washer to act as a jam nut.
Screw the elevator bolt in from the back. Use an elevator bolt with appropriate length for application.
Mounting
Feed the spring nuts into the channel.
Use the horizontal spacer guide to line the nuts up so they match the hangers, I cut a piece of slotted steel to keep the nuts at the proper spacing.
Next is a square washer,
Then a round washer,
Then a lock washer,
Then either an appropriate length bolt or knob with bolt.
Hardware
Hangers and Horizontal Spacer:
Slotted Steel, 1 3/8 inch 14 gauge, 3/8 inch holes spaced 3/4 inches apart.
Bracket and Ammo Can Attachment:
1/4"-20 2" bolts x 4 (used to attach hanger and bracket to the ammo can)
1/4"-20 3/4" bolts x 2 (used in top hole to support/stiffen the 14ga hanger)
1/4" washers x 12
1/4" lock/split washers x 6
1/4" nuts x 6
Utili-Track Attachment:
3/8"-16 1 1/2" bolt x 2 (1 1/2" is the max depth for the side rails shorter may work as they don't have to go all the way to the rear of the channel, the rear rail is shorter so 1 1/2" will be too long)
3/8" washer x 2
3/8" lock/split washer x 2
3/8" Strut Channel Spring Nut for 1 5/8" channel x 2
3/8" Strut Channel Square Washer for 1 5/8" channel x 2
Stabilizer Feet
3/8" Elevator Bolts 2" x 2, (depending on where you put it and if you back it with a magnet or not, longer elevator bolts would be better, maybe 2 1/2 - 3")
3/8" nuts x 4
3/8" washer x 2
3/8" lock/split washer x 2
Optional:
Alternative to 3/8"-16 1 1/2" bolt is an equivalent knob with integrated bolt, although there isn't a lot of room for the knob handle and the lid to open, I'm okay with the lid flexing to open around the knobs.)
4 in. Magnetic Parts Holder (like Harbor Freight, put behind elevator bolt/stabilizer foot)