1 / 24
Tunable chromatic mbira/kalimba/thumb piano musical instrument! — image 1
1 / 24

Tunable chromatic mbira/kalimba/thumb piano musical instrument!

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is (almost) fully 3d printed mbira/kalimba musical instrument, just need some glue, screws/nuts for assembly!The…

Rating
0 / 5
Likes
17
Downloads
34
Makes
0
Views
472
Reviews
0

Updated at source:

Model information

Category
Music
License
Creative Commons — Attribution — Share Alike

This is (almost) fully 3d printed mbira/kalimba musical instrument, just need some glue, screws/nuts for assembly! The sound is low but can be heard, good for practicing or playing alone without disturbing anyone and getting into trouble. Essentially need to assemble as told for best order of steps to do, tuning needs patience and better if done by ear in addition to tuner, with phone tuners i see sometimes it's detecting incorrectly due to noise and not loud enough, i tune it by also playing familiar melodies to see if they sound correct after initial each note tuning. The current range i tuned into is E2-E4 inclusive, it'll probably work within range of C2-C4 to G2-G4, if too low then sound will be weak, if too high then hard to tune and noisy sound. Total weight is approx. 500gram, around 400gram are printed parts.

Print settings: Use PLA or anything stiffer than that for all parts, TPU will not work at all, ABS probably not, PETG probably ok. Recommended to always print with 100% infill for strength, i made walls 2mm which i see should been thicker but it works too and uses less filament. At least tongues (the sound making sticks) must always be 100% infill. Add supports, without supports can work but needs quite lot of sand/fixing after print, recommended to put light supports, with 0.4-0.6 z distance. Colors: i printed body in black, sound bridges with semi-transparent weak green glow, tongues: white keys in white daytime blue glow in dark, black keys in orange daytime orange glow (blue and orange glow looks good together with high contrast and almost equal glow, see in picture), tongue fillers in black. You can print any color, just make sure tongues are well visible for playing.

Printing parts list: Body: 1x Box top 1x Box bottom 1x Sound bridge for white 1x Sound bridge for black

Tongue fillers for black keys (i.e. for the keys that don't have accidentals) and ends, can print more of them since they are tiny sized, 10x10x2 and 4x10x2 millimeters: 4x tongue filler ends 3x tongue filler center

Tongues (assuming to be tuned to E2-E4 with PLA, but may vary slightly), sizes in mm: White tongue counts per size: 2x100 2x90 3x80 5x70 3x60

Black tongue counts per size: 2x90 3x80 3x70 2x60

Hardware: 31x 3mm screw 8-15mm length (10mm is good), along with hex nuts and washers. This is for washers. 44x 4mm screws 8-20mm length (10mm is good), along with hex nuts and washers. This is for body. Some glue, i used UV resin, this is to glue some of nuts in place before assembling so they won't fall down.

Instructions, when screwing anything, do it much tight, otherwise there will be unwanted noise while playing. Step 1: Print the above mentioned parts and remove supports. See the images of what it looks like. Step 2: Glue the nuts that are located on box top object on corners and sides, these that will screw into body, others can be skipped gluing. See images. Step 3: Put the screw/nut/washers on sound bridges as shown in images, nuts at rectangular holes, screw and washer at top. Step 4: Screw the bridges into box top, note the black keys bridge must be put such that it'll entirely fit into the area and well aligned, see the image, here the nuts not needed to be glued as they are readily reachable with hands. Step 5: Screw the box top into bottom. Here it's good if nuts are glued upfront, otherwise if some fall during screwing you may need to start all over this step! And also screw the pillars of box bottom into top, preferably put nut into pillar and screw at box top. Step 6: check to make sure body sits evenly on table/flat surface, if it's much uneven then glue something like flat piece of plastic to make it almost even. Step 7: Add anti-slip pads or something, while playing it'll slip a lot, put very sticky silicone pads or similar. I had put big ones, but small ones will work too, put on 4 sides or more. If not put it'll still play, but you'll need to hold it with other hand to not slip. Step 8: Put the white key tongues and tune then, put the 2 tongue end fillers at ends of bridge. For tuning, unscrew the left and right holding screws, move upward (shortening) for higher note, and elongating for lowering. For low notes can do bigger 1-2mm steps, for higher notes need to be very precise short movements, otherwise it'll jump too many notes. This needs patience to do. Step 9: Now do the same for black keys, and the places that don't have black key put the tongue center fillers. Recommended to fully tune white keys as when blacks are put it'll be hard to re-tune white keys, needing to unscrew some black keys.

Issues and notes: -It will periodically go out of tune especially if room temperature gets much different, may need re-tuning sometimes. -There's some noise in higher notes, probably body not stiff enough or has some natural resonance on some keys. -Body is bit weak but alright, will do more thick next time, but this will work for 1 octave version when i make. -Body fixing screw holes are bit offset from center, it works anyway, but will fix it next time. -While playing the left/right of current key may be accidentally pressed, need to either make wider tongues or more distance. -Later considering to make bigger 3 octave version, and small started 1 octave version. -It seems bit uncomfortable for long playing due to box being short on bottom side of tongues where hands will touch or rest on, considering to make it longer.

Videos (i made them louder, it's hard to hear otherwise): https://youtu.be/9w_67DU0O1I

Let me know suggestions to improve. Happy printing and playing!

Category: Music

Tags