1 / 13
Tree Top Legend of Zelda Wingcrest — image 1
1 / 13

Tree Top Legend of Zelda Wingcrest

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Model from the video game for mounting on top of a Christmas tree.

Rating
0 / 5
Likes
2
Downloads
5
Makes
0
Views
48
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

IMPORTANT:  holes have been sized to print correctly at 300% scale!  Scale all stl parts in Prusaslicer before slicing.  3mf files have already been scaled.

Modified the excellent model by fasteddy to function as a tree-top ornament.  With some fairly challenging soldering it lights up the "feathers" and TriForce.

There are other ways the lighting could be accomplished, but here are the parts I used:

  • 2 x M3x8 socket head screws (to mount the tree top mount to the wingcrest)

  • 2 x M3x25 screws (to fasten the 3 layers of the TriForce light holder together)

  • 8 x 3mm Elegoo white LEDs (3-3.4V 20mA) (2 banks of 4)

  • 3 x 3mm Elegoo yellow LEDs (2-2.2V 20mA)

  • 3 x 1.2 kOhm resistors

  • 12V/2A power adapter with 5.5mm/2.1mm male barrel plug (https://a.co/d/cqsjIPr)

  • Female barrel plug 5.5mm/2.1mm "pigtail" (https://a.co/d/7Lr6cgR)

  • some other wire - your choice!  I measured 25 mA current overall so small gauge is better/easier to work with

  • wire braid/cover/loom to protect the power wires to the adapter plug (0.2")

  • hot glue gun (to anchor the LEDs in the holes and ensure they don't move, and the leads stay separated

Printing:

  • Medium Grey PETG for 1st filament for main body of wingcrest

  • Translucent PETG for 2nd filament for feathers and triforce

  • Carbon Fiber PETG for tree top holder and other parts

  • 0.2 mm layers, 0.4 mm nozzle (hardened), structural profile, gyroid 15% infill, 2 perimeters

Wire as follows:

  • solder the middle of the long lead (+ve) of 4 white LEDs to a bare wire, spaced appropriately for the holes on one side pointing at the feathers.  Run this wire to the "top" of the mount.

  • solder the shorter lead (-ve) the same way, but run this wire to the "bottom" of the mount.

  • do the above for the other 4 white LEDs for the other side.

  • solder 2 small (22-24 gauge) wires to the leads of the yellow LEDs - I used red for the +ve lead and black for the -ve.  Trim excess from leads.

  • this is the tricky part!  Lay out 2 of the yellow LEDs on the bottom piece in the 2 depressions.  You must ensure the tip of the LEDs don't protrude from the holder or it won't slide into the TriForce.  Figure out how to bend the leads so that they don't touch the opposite polarity, and the 2 nearest ones will have to route around the 3rd LED on the next level.

  • I attached the middle holder at this point temporarily with 2 short M3 screws, and placed the 3rd LED in the depression.

  • Solder the +ve leads together with a 50 mm length of 22 gauge wire.

  • Solder the -ve leads together with a 50 mm length of 22 gauge wire.

  • Remove the temporary screws and fasten the top of the triangular LED holder to the other 2 pieces, threading the wires through the centre slot.  This is when you want to ensure the leads aren't touching the wrong things.

  • Solder a resistor to the +ve wire from the yellow LEDs.

  • TEST the yellow LEDs by putting 12V on the end of the resistor, and ground the other lead.

  • TEST fit the LED holder into the TriForce - last chance!

  • At this point I used a glue gun, while the LED holder was still in the TriForce, to fill the centre slot so that nothing ever moved and shorted out.

  • solder a resistor to each of the left and right 4-white LED banks (+ve lead).

  • insert the yellow LED triangular holder into the hole in the tree top mount.

  • Option 1:  extend the power leads if necessary from the female barrel connector so that the connector can sit well below the tree top mount with the wires fed through the mount itself into the top cavity.

  • Option 2:  feed the power leads through the hole in the back cover.

  • fasten the female barrel connector with the provided washer and nut to the bottom of the barrel connector cover, then feed the wires through the top of the cover and screw it onto the barrel connector.

  • use wire braid along the power wires - I zip-tie it at both ends.  The end inside the cavity should have something to prevent it being pulled out - zip-tie plus hot glue at a minimum.

  • solder the free end of all 3 resistors to the +ve lead from the female barrel connector.

  • solder all the -ve wires together with the -ve lead from the female barrel connector.

  • TEST the lights before you glue them in place.  Do this with the wingcrest attached to verify you are happy with the lighting - should be nice and even

  • also, test fit the back cover to ensure the tabs aren't interfering with any wires

  • once you're happy, use a glue gun to fill the center hole where the yellow LEDs are (if you didn't already), and fill each white LED hole.  Tack down any wires that are misbehaving.

  • put on the back cover.

  • Use 2 M3x8 screws to attach the tree top mount to the wingcrest.

Tags