1/4 Scale Federal Signal Thunderbeam Siren
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
DC powered 1/4 scale outdoor warning siren
- Rating
- 0 / 5
- Likes
- 11
- Downloads
- 47
- Makes
- 0
- Views
- 700
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Toys & Games
- License
- Creative Commons — Attribution — Noncommercial
DISCLAIMER
The information provided here is offered on an AS-IS basis only. While I have efforted to make this helpful to you, I do not offer any warranty or guarantee of any kind regarding any aspect of this information. The information below may be subject to change without notice. The full risks as to the use of this information are assumed solely by the model builder.
This needs a bigger printer with a minimum of 320mm x 320mm to print all the pieces whole... you will need to section some parts to fit them on smaller build plates.
To Assemble this model you will need get these or equivalent.
https://www.amazon.com/dp/B07P6X8QM1 2.3 to 4mm coupler and a 2 to 4mm coupler
https://www.amazon.com/dp/B09LS1123F DC generator
https://www.amazon.com/dp/B0CHRXQYS7 Motor driven reduction Gear Set 15 RPM
https://www.amazon.com/dp/B0BB2V8PNK 390 Motor
https://www.amazon.com/dp/B0D2XCH9R2 10F super capacitor
https://www.amazon.com/dp/B0BX7HNJTJ Power Regulator
https://www.amazon.com/dp/B09637K9FK Steel Shaft
https://www.amazon.com/dp/B07Z3FT4FD 4x10x4mm bearing
https://www.amazon.com/dp/B085NDM5WV 40x50x6mm bearing buy 2
The frame needs to use Socket Head M4 bolts. The bottom of the siren needs to use button head bolts
The Impeller and rotator drive hub are held together with M3 bolts that need to be at least 50mm length.
Build the frame up first. Make note of what each arm piece is as the top pieces and bottom pieces are different.
Once you assemble to the rotator you can literally drop the rest of it into place on top of it. The top and bottom rings have slots which will slip into the socket heads on the frame. The bars that the screens bolt to screw into the rings and hold them in place.
The intake guard accepts one of the 4mm bearings called for. Without it the long shaft will impart vibrations and make it impossible to keep to impeller from rubbing.
again like with my other models, Unless noted, I don't use threaded inserts. Normal bolts will cut their own threads into the plastic the first time you put a bolt into them.
There are two hubs for mounting the impeller to the motor. The 2.3 to 4 mm coupler mounts onto the 390 motor. The rotor hub press fits on the 2.3 to 4mm coupler. There are holes in the hub to line up with the set screws on the coupler. Back out the screws to lock the hub on the coupler. The impeller fits over the rotor hub. The rotator drive hub goes onto the intake side of the impeller. Those long 50mm M3 bolts go through both hubs and the impeller and holds everything together. The 4mm shaft is a press fit into the drive hub which in turn goes through the bearing in the intake shield. the rotor hub has little collars on the them for wobble removal. By tightening down the nuts you can slightly crush the collars and remove any wobble from the rotor. If you ruin the hub in anyway you can reprint the hub without doing the whole rotor. The impeller itself has holes in it around the circumference to
The motor holder mounts on the stator. Both the stator and motor mount have insets to press M4 nuts into them... The mount then bolts to the stator. The motor will slide into the mount and will be held buy the 6 M4 bolts
To align the motor in the stator... those six screws in the motor holder adjust the placement and tilt of the rotating assembly. You need to adjust each screw to center the rotor up. For each screw you tighten on the top, you need to loosen another one on the top, same for the bottom as well. The assembly will move in the direction that the screw is pushing it
If you have that 390 motor I linked above you can take a second coupler and put it on the back shaft and use it to give the rotating assembly a finger spin to check for rubbing. Just keep at it until you find the sweet spot. It takes myself about 5 minutes to get it dialed in.
the whole STH-10 part of the siren mounts to the frame using holes in the stator the horns for the STH-10 would use. The top horn/cover on the stator bolts down the same way using holes top side on the stator the the horns would bolt to
The 4mm steel shaft to drive the rotator will need to be cut to approximately 155mm to reach down the rotator. The rotator holder has insets to press fit the generator and reduction gear set. Solder the wires from the generator to gear set motor before inserting. There are slots in the side of the receiver for the wires to slide in without getting caught. The small gear press fits on the shaft of the gear reducer while the ring gear gets super glued into a groove that's in the deflector base. you can vary the amount you push the gear reducer into the rotator holder to line it up with the ring gear. the 2 to 4mm coupler recieves the shaft coming down from the main motor and attaches to the generator.
the two giant bearings go on the rotator base. The bottom one rests on a stop in model while the top on is held in place by four M2 screws. the deflector base slides over the rotator base and when you have the rotator hold in place it will lock it down.
The rotator will start late and stop early because of the generator/motor setup. However this is a far simpler setup to construct for rotation than trying to create and build an 1800:1 reduction gear set and getting it to fit comfortably in the space it has to go into. The bearings will make for smooth and easy rotation and despite being really tiny, the generator/motor pair has no trouble rotating the deflector.
The screens can be printed flat, they will wrap around the top and bottom rings and have places to bolt on. they are keyed. use button head bolts only to secure the screen holder bars to the rings as the screens have holes in them that line up with these heads.
The power regulator is the standard higher power unit I use. Set to 3.5 volts for siren speed. You can stuff the 10 farad supercap into the power box if it won't fit under the motor cover. Simply wire it into the circuit for longer wind downs. For a power source a standard wall wart will not work. You'll need something that can source 3 or 4 amps because if the voltage on the supply drops to a certain point the power regulator will shut down and the siren will never get up to speed.