Nozzle wiper & purge bucket for RatRig V-Core 4
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A simple but effective nozzle wiper & purge bucket for the vcore4
- Rating
- 0 / 5
- Likes
- 9
- Downloads
- 32
- Makes
- 0
- Views
- 375
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial
Nozzle Wiper & Purge Bucket (VCore 4 – Non-IDEX Only)
This nozzle wiper and purge bucket assembly is designed specifically for the VCore 4 non-IDEX configuration. It provides a clean and repeatable way to wipe the nozzle and capture purge material, with a magnetically retained bucket for easy removal and cleaning.
⚠ Not compatible with IDEX setups.
Bill of Materials (BOM)
2 × M6 hammer nuts
2 × M6 × 12 mm screws
2 × DIN562 M3 square nuts
2 × M3 × 10 mm screws
1 × 9 mm GT2.5 belt (RatRig BOM)
2 × M3 neodymium magnets (6 × 3 mm)
Installation Instructions
Cut the GT2.5 belt to 4 teeth and assemble the nozzle wiper mechanism.
Mount the wiper holder to the frame using the M6 hammer nuts and M6 × 12 mm screws.
Install the M3 square nuts and M3 × 10 mm screws where required to secure the assembly.
Insert the neodymium magnets into the purge bucket and place the bucket into position.
Power on the printer and dial in the final location of the wiper and bucket to ensure proper nozzle contact and clean purging.
Firmware & Macro Integration
Use the macro to control the wiping and purging sequence.
[gcode_macro NOZZLE_WIPE]
description: Wipe the nozzle
gcode:
### DOESNT HANDLE IDEX PRINTERHandle toolhead settings
CACHE_TOOLHEAD_SETTINGS KEY="nozzle_wipe"
SET_MACRO_TRAVEL_SETTINGS
RATOS_ECHO PREFIX="Wiping" MSG="Wiping nozzle with nozzle wiper.."
set current toolhead default
{% set current_toolhead = 0 %}
save gcode state
this is a macro where copy and mirror mode is possibly in use
SAVE_GCODE_STATE isnt IDEX aware, we have no other chance than to skip it
klippers built in dual carriage save state is buggy and creates to many side effects
{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
SAVE_GCODE_STATE NAME=nozzle_wipe_state
{% endif %}
config
{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
# Home if needed
MAYBE_HOME
# TODO: Variables
{% set x_start = 555 %}
{% set y_start = 173 %}
{% set y_end = 140 %}
{% set wipe_qty = 3 %}
DEBUG_ECHO PREFIX="NOZZLE_WIPE" MSG="x_start: {x_start}, y_start: {y_start}"
Absolute positioning
G90
Relative extrusion
M83
move close to wipe position along the edge of the bed
{% set target_y = y_start + 10 %}
{% set current_y = printer.toolhead.position.y %}
{% set detour_x = x_start - 20 %}
RATOS_ECHO PREFIX="Wiping" MSG="Moving to {x_start}, {target_y} along the edge of the print area.."
{% if current_y <= target_y %}
# Detour to avoid nozzle brush
G1 X{detour_x} F{speed}
G1 Y{target_y} F{speed}
{% endif %}
# Final approach
G1 X{x_start} F{speed}
G1 Y{target_y} F{speed}
# Wiping
RATOS_ECHO PREFIX="Wiping" MSG="Starting the wipe.."
{% for wipes in range(1, (wipe_qty + 1)) %}
G1 Y{y_start+10} F3000
G1 Y{y_end-10} F3000
{% endfor %}
# Moving past
G1 Y{y_end - 30} F{speed}
restore gcode state
this is a macro where copy and mirror mode is possibly in use
SAVE_GCODE_STATE isnt IDEX aware, we have no other chance than to skip it
klippers built in dual carriage save state is buggy and creates to many side effects
{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
RESTORE_GCODE_STATE NAME=nozzle_wipe_state
{% endif %}
Handle toolhead settings
RESTORE_TOOLHEAD_SETTINGS KEY="nozzle_wipe"
For full automation, this setup can be integrated into the RatOS print start routine.
[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode:
{% set extruder_first_layer_temp = params.EXTRUDER_TEMP %}
{% set first_wipe_temp = (extruder_first_layer_temp|float) * 0.9 %}
{% set second_wipe_temp = (extruder_first_layer_temp|float) * 0.7%}
SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={first_wipe_temp}
TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={first_wipe_temp} MAXIMUM={first_wipe_temp + 5}
NOZZLE_WIPE
SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={second_wipe_temp}
TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={second_wipe_temp} MAXIMUM={second_wipe_temp + 5}
NOZZLE_WIPE
SET_HEATER_TEMPERATURE HEATER="extruder" TARGET=0
G28 Z # To Force a new homing after cleaningYou may also tweak your runout pause location to load/unload on top of the bucket
This allows the nozzle to be wiped automatically at the beginning of each print.
Belt holder is from: https://www.printables.com/model/1397846-belt-brush-v2
Bucket design: https://github.com/Bloodpack/Decontaminator_Bucket
Macro is heavily inspired from blob macro from RatOS: https://github.com/Rat-OS/RatOS-configuration/blob/v2.1.x/macros/priming.cfg#L219