1 / 15
Fanntik V8/10 Apex slim storage and charging frame — image 1
1 / 15

Fanntik V8/10 Apex slim storage and charging frame

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Stand for the Fanttik V8/10 apex slim and accessories with charging option

Rating
5 / 5
Likes
19
Downloads
189
Makes
4
Views
635
Reviews
4

Updated at source:

Model information

Category
Organizers
License
Creative Commons — Attribution — Noncommercial — Share Alike

Ladeschale Fanntik V8 apex Slim

Ich habe mir den Fanttik slim V8 apex zur Reinigung meines 3d Druckers und anderer Geräte gekauft. Leider wird nichts zur Aufbewahrung der Zubehörteile mitgeliefert. Ich habe eine Aufbewahrungsrahmen entworfen der die meisten Teile aufnimmt. Der V8 wird wenn er im Ständer steht geladen. Ich habe den Ständer in PLA gedruckt. Kojak hat die Variante 1 des Modells mit dem V10 verwendet. Variante 2 sollte ebenfalls mit dem V10 kompatibel sein. Wäre schön wenn es jemand probiert. 
 

Variante 1 mit Zwischenstecker

Diese Variante  kann auch ohne Ladeanschluß benutz werden. Dann entfällt die Montage des Ladenanschlusses. 

Als Ladeanschluß habe ich einen JSAUX USB C Winkelstecker 90 Grad verwendet.

Ich habe festgestellt das das mitgelieferte Ladekabel nur mit 1,2A lädt. Mit einem USB-C PD Kabel lädt der V8 mit 3A.

 

Montage:

Diese Variante kann auch ohne Ladeanschluß benutz werden. Dann entfällt die Montage des Ladenanschlusses.

Der  90 Grad Stecker wird in die Aufname gesteckt. Dann wird die Steckerfixierung in die Führungsschlitze der Aufname gesteckt. Nun wird die Aufname an die Ladeschale mit den M2x8mm Schrauben mit Gefühl angeschraubt. Nach Fest kommt Lose !!! An den Ausgang des Winkesteckers wird das Ladekabel angeschlossen.  


Benötigte Teile:

  • 1 X USB-C JSAUX USB C Winkelstecker 90 Grad Amazon ASIN: B0B77CJD7T

  • 2 x Rundkopfschraube selbstschneitend M2*8mm zur Montage Winkelstecker

  • 3 x Rundkopfschraube selbstschneitend M3*16mm zur Wandmontage

Variante 2 für original Kabel

Hier entfällt der Zwischenstecker. Das Kabel wird in das Unterteil eingelegt und der Stecker von oben einführt  bis er nicht weiter hinein geht. Jetzt wird die Klemmfixierung in der Führung  gegen den Knickschutz des Kabels gedrückt und in das Unterteil eingerastet. Anschließend wird das Unterteil in die Basis montiert und durch verdrehen fixiert. (siehe Bilder)

4.02.2026 - Variante für das mitgelieferte Ladekabel hinzugefügt

6.02.2026 - kleine  Optimierung der Basis und der Kabelhalterung bei  Variante 2 

10.02.2026 - Varinte 2 für das Skadis System angepaßt und kleine Optimierungen. Skadis Montageteil  hinzugefügt. 

20.03.2026 -Kompatibilität für V10 apex slim hinzugefügt

Charging cradle Fanntik V8/10 apex Slim 

I bought the Fanttik slim V8 apex to clean my 3d printer and other devices. Unfortunately, nothing is included to store the accessories. I designed a storage frame that holds most of the parts. The V8 is charged when it is in the stand. I printed the stand in PLA. Kojak used variant 1 of the model with the V10. Variant 2 should also be compatible with the V10. It would be great if someone could try it.

Version 1 with adapter plug

 As a charging connection I used a JSAUX USB C angled plug 90 degrees. I have noticed that the included charging cable only charges with 1.2A. With a USB-C PD cable, the V8 charges at 3A. 

This stand can also be used without the charging port. In this case, the charging port does not need to be installed.

Assembly:

The 90-degree connector is inserted into the holder. Then, the connector retainer is inserted into the guide slots of the holder. Now, the holder is carefully screwed onto the charging cradle using the M2x8mm screws. Be careful not to overtighten! The charging cable is connected to the output of the angled connector. The guide is attached to the V8 with double-sided adhesive tape when it is plugged into the charging port.

Parts Needed: 

  • 1 x USB-C JSAUX USB C Right-Angle Plug 90 Degrees Amazon ASIN: B0B77CJD7T

  •  2 x round head screw self-snowing M2*8mm for mounting angled plug

  •  3 x round head screw self-snowing M3*16mm for wall mounting

 

Version 2 for original cable

 This version does not require an intermediate connector. The cable is inserted into the base, and the connector is inserted from above until it stops. The clamping mechanism is then pressed against the cable's strain relief and snapped into place in the base. Finally, the base is mounted into the socket and secured by twisting. (see pictures)

4.02.2026 - Added variant for the included charging cable 

6.02.2026 - Small optimization of the base and the cable holder for variant 2

10.02.2026 - Varinte 2 adapted for the Skadis system and small optimizations. Added Skadi's mounting part.

20.03.2026 - Added compatibility for V10 Apex Slim.

Tags